background image

TF2048902-KK-00 ENG                                                     

            Page 16 of 16                                                      20111003 V.1

LIMITED WARRANTY

1. Manufacturer warrants this Product to be free from defects in workmanship and materials for a period of 

Ninety (90) days from the date of purchase, PROVIDED claims are submitted, in writing, with proof of 
purchase.

2. If any part of this item fails because of a manufacturing defect within the Limited Warranty Period, 

Manufacturer offers to replace such part(s) provide that such parts have not been improperly repaired, 
altered, or tampered with or subject to misuse, abuse or exposed to corrosive conditions. This Limited 
Warranty is, however, subject to certain limitations, exclusions, time limits and exceptions (Hereinafter 
“Conditions”) as listed below. Read these Conditions carefully.

3. This Limited Warranty shall be limited to the replacement or repair of any part(s) which Manufacturer 

determines, after reasonable examination, to have been defective at the time of manufacturing and 
manufacturer’s obligation(s) shall be limited to replacement, if any, of defective part(s) which shall be 
shipped at Original Purchaser’s expense to Original Purchaser’s designated shipping address.

4. This Limited Warranty is given to and covers the 

ORIGINAL PURCHASER ONLY 

and such coverage 

terminates Ninety (90) days from the date of purchase.

5.

DAMAGE LIMITATION WARNING: 

IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR ANY 

INCIDENTIAL OR CONSEQUENTIAL DAMAGES, INCLUDING (BUT NOT LIMITED TO) LOSS OF USE 
OF THE PRODUCT, LOSS OF TIME, INCONVENIENCE, EXPENSES FOR TRAVEL, TRANSPORTATION 
LODGING EXPENSES, LOSS BY DAMAGE TO PERSONAL PROPERTY OR LOSS OF INCOME, 
PROFITS OR REVENUE.

6.

MANUFACTURER’S OBLIGATION:

Manufacturer’s liability shall be limited to the delivery of a good, 

merchantable Product and, if necessary, the repair or replacement, at manufacturer’s option, of any 
defective part or unit.

7.

TRANSFER LIMITATIONS:

 This Limited Warranty is not assignable or transferable. It covers only the 

original purchaser.

8.

RESERVED RIGHT TO CHANGE:

 Manufacturer reserves the right to make changes or improvements to 

products it produces in the future without imposing on itself any obligations to install the same 
improvements in the products it has previously manufactured.

9. This Limited Warranty gives the Original Purchaser specific legal rights but there may be other rights which 

vary by jurisdiction.

IF CUSTOMER SERVICE BECOME NECESSARY:

1.

The Original Purchaser is responsible for shipping and handling charges of the returned item(s) 
and replacement parts, if any.

2.

All parts to be replaced will need to be shipped before replacement items will be sent.

3.

Follow the Customer Service Representative’s instructions exactly. If a return is necessary, it must 
be packed carefully and shipped prepaid.

Should you encounter any problems,

CONTACT US FIRST

DO NOT return product to the store!

RANKAM METAL PRODUCTS MANUFACTORY LTD.

18/F., NEW LEE WAH CENTRE,

88 TOKWAWAN ROAD,

KOWLOON, HONG KONG

CUSTOMER SERVICE

1618 W. Rosecrans Ave.,

Gardena, CA 90249,

U.S.A.

1 – 888 – 837 – 1380

[email protected]

Summary of Contents for TF2048902-KK-00

















Reviews: