Ranger R30XLT Installation And Operation Manual Download

Page: 8 / 48

fEATuRES / SPECIfICATIONS

MODEL - R30XLT

Type of Drive System

Air / Electric

Motor

Dual Voltage 110/220V 50/60HZ 1 Ph.

Air Requirement

110-175 PSI (7.6 - 12.1 BAR)

Wheel Clamping Method

4 Rim-Guard Clamps - Internal / External

Table Clamping System

Dual Pneumatic Cylinders

Bead Breaking System

Pneumatic Blade / Dual Settings

Turntable Speed 360-Degree Rotation

8 Seconds

Tool Holder

Manual Lock

Adjustable Turntable Clamps

Standard

Inflation System

Standard

Inflation Pressure Regulator/Limiter

Standard

Water Filter

Standard

Oiler / Lubricator

Standard

Air Regulators

(Inflation Pedal, Assist Tower)

Standard

Bead Lifting Tool

Standard

Large Soap / Lubricator Bucket

Standard

Brush

Standard

Tower Design

Rigid Fixed

Powerful "Turbo -Blast" Bead Seating System

Standard

Tire Inflation

Standard

Tool Tray / Bin Storage

Standard

Internal Wheel Clamping Capacity *

12" – 32" (305 mm – 813 mm)

External Wheel Clamping Capacity *

11" – 31½” (280 mm – 800 mm)

Turntable Tire Width Capacity (Mounting)

3½" – 16" (89 mm – 406 mm)

Bead Breaker Tire Width Capacity (Demounting)

2½" – 16" (63.5 mm – 406 mm)

Maximum Tire Diameter

49" (1245 mm)

Shipping Weight

R30XLT:620 lbs. (282 Kg)

Specifications are subject to change without notice.

* NOTE: Internal and External Wheel clamping dimensions do not translate directly to rim or tire sizes as wheel clamping
points may vary by manufacturer.

1. Pallet jack or forklift for moving crate

2. Forklift or Shop crane

3 Utility knife

4. Crow bar or pry bar.

5. Tin Snips or Sheet Metal Snips

6. Hammer

7. Open end metric wrenches and/or socket set

8. Phillips and Slot head screw drivers

9. Metric Allen Key set

Parts required but not supplied:

1. Teflon tape

2. Air fitting to match shop Air Supply line

3. Tool Oil

4. Anchor Bolts and Shims (if Anchoring)

TOOLS REquIRED fOR ASSEMBLY and INSTALLATION

SECTION 5 - fEATuRES / SPECIfICATIONS

Summary of Contents for R30XLT

















































Search results

Summary of Contents for R30XLT

Reviews:

Related manuals for R30XLT

Brands by name

Popular brands

Ranger R30XLT, Installation And Operation Manual

Search results

Summary of Contents for R30XLT

Reviews:

Related manuals for R30XLT

Brands by name

Popular brands