manualshive.com logo in svg

Range Road 6022, Owner'S Manual, Page: 8 / 39

Share
Download
Range Road 6022 Owner'S Manual Download Page 8

 

Range Road Enterprises Ltd 

 

Box  5  Site  9  RR1 
Lacombe, AB  T4L 2N1 
www.range-road.ca 

 

-

 

Do not fill fuel tank to the top. Leave a little room for the fuel to expand as  

  needed.

 

-

 

Refuel in a well-ventilated area only

 

 

 

 Specifications 

 

Model:  

RR6022A/B 

RR2026AW 

 RR6032A/B

 

 Fuel Type                         87+ octane unleaded         87+ octane unleaded 

      87+ octane unleaded  

 
 Fuel Capacity  

          1.4Gal (5.4 L) RATO           1.7 Gal (6.5L)                         2.4 Gal (9L) RATO  

                                              0.8 Gal (3L) B&S                                                               1.95 Gal (7.4L) Kohler  
 

 

Note: Engine specifications are found in the engine manual supplied with this sawmill. 

 

TO PREVENT SERIOUS INJURY:

 

Operate  only  with  proper  spark  arrestor(s)  installed.  Operation  of  this  equipment  may  create 
sparks that can start fires around dry vegetation and brush. A spark arrestor may be required. 
The  operator  should  contact  local  agencies  for  laws  or  regulations  relating  to  fire  prevention 
requirements.

 

Assembly

 

Read all of the safety precautions and warnings in this manual before setting up or using this product.

 

 

 

 

 

 

Summary of Contents for 6022








































Reviews:

No comments