manualshive.com logo in svg

Rane TTM 52, Operator'S Manual, Page: 6 / 8

Share
Download
Rane TTM 52 Operator'S Manual Download Page 6

Manual-6

Replacement Wear Parts

Replacement Phono/Line switch assembly: ST 1

Replacement Fader Assembly:

FT 45

All three faders use the same part.
Follow steps A and C in the Fader Cleaning instructions to the right.

Replacement assemblies available from your local Rane dealer.

Figure 4. Phono/Line switch rotation or replacement

Rotating or Replacing Phono/Line
Switches

1. Remove the metal faceplace with a #2 Phillips screwdriver.
2. Remove nut and key washer while holding bottom of switch assembly.
3. Rotate or install switch with key pointing to desired PHONO position.
4. Install key washer.
5. Install nut, tighten securely with a 5/16" nut driver.
6. Replace faceplate.

Fader Cleaning

With heavy use in harsh environments, the

faders may need lubrication. This treatment
extends longevity and can make used faders as
good as new. The fader assembly must be
removed from the TTM 52 for proper cleaning.
We recommend any of the following cleaning
solutions:

Caig Cailube MCL 100% spray lubricant
Caig Cailube MCL 5% spray cleaner
CRC 2-26

Order CaiLube MCL

®

 from:

CAIG Laboratories, Inc.
12200 Thatcher Ct.
Poway, CA  92064
Phone 619-486-8388
Fax 619-486-8398
Web  http://www.caig.com

CLEANING INSTRUCTIONS

A. Front panel removal

1. Disconnect the power cord.
2. Remove (3) slide fader knobs.
3. Remove (4) #4-40 front panel screws.
Faders and switches are now accessible.

B. Fader assembly removal

To remove any single fader:
1. Remove (2) 3mm screws.
2. Draw fader assembly out through hole.
3. Remove ribbon cable.

C. Fader cleaning

1. Hold the fader assembly away from the

mixer.

2. Position the fader at mid-travel.
3. Spray cleaner/lubricant into both ends of the

fader.

4. Move the fader over its full travel back and

forth a few times.

5. Shake excess fluid from the fader assembly.
6. Wipe off excess fluid.

D. Fader assembly installation

1. Connect the ribbon cable to the fader

assembly.

2. Place the fader assembly in position with the

ribbon connector to the right side or top, as
shown.

3. Line up the fader screw holes with the mixer

mounting holes.

4. Install (2 provided) 3mm screws. Using the

wrong screw will ruin the fader!

5. Replace the front panel and knobs.

Summary of Contents for TTM 52









Reviews:

No comments