LP0253
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
Email:
Page | 7
•
Gently slide the OEM rear panel back in and locate the cover plate on the inside. Push the OEM push pins back
in their original position, securing the cover plate.
•
If using OEM indicators connect these to the OEM sub loom removed earlier.
•
If using mini indicators connect these to the indicator connectors (item 12) and connect this to the OEM sub
loom removed earlier. A set of R&G resistors (RGR0001) may be required to achieve the correct flash rate.
•
To connect the OEM licence plate illuminator wiring to the R&G licence plate illuminator the OEM wiring will
need to be ‘cut and shut’. To do this cut off the OEM licence plate illuminator connector leaving 100mm of
wiring attached. Strip the ends of the wires and fit female bullet connectors (item 11) to the exposed ends of both
wires. Connect this to the licence plate illuminator and connect the newly ‘cut and shut’ OEM connector to the
OEM sub loom.
•
Connect the OEM sub loom to the main loom.
•
At this stage it is advisable to check operation of all lights. If lights fail to illuminate swap the connectors.
•
Tidy the wires using cable tie provided and tuck into the space where wires were originally located.
•
Refit both rear side panels, rider seat and pillion seat as original.
•
Refit the licence plate (it may require drilling).
•
Please check the operation of all lights before riding the motorcycle.
•
I
MPORTANT: IF FITTING A FULL-SIZE LICENCE PLATE AND PLACING IT FAR DOWN ON
THE LICENCE PLATE HANGER, THERE IS A SMALL CHANCE OF THE LICENCE PLATE
HITTING THE BACK WHEEL UNDER HEAVY LOAD AND OVER LARGE BUMPS IN THE ROAD.
IT IS YOUR RESPONSIBILITY TO CHECK FOR THIS POSSIBILITY AND TAKE AVOIDING
ACTION. FAILURE TO CHECK THIS COULD RESULT IN SERIOUS INJURY.
•
Depending on local laws, attach enclosed reflector (item 15) in an appropriate location
ISSUE 1 21/08/2018 (HB)
Digital copies of these instructions are available to download from
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it
has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other
services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is
responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G
shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or
maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident
or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for
indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service
concerned. These terms do not affect the Buyer’s statutory rights.
R&G RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct
from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of
R&G. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The
customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your
statutory rights and does not refer to faulty goods.
