R&G LGFK0023 Fitting Instructions Manual Download Page 3

Page 

3

 of 

9

    

 

LGFK0023

 

 

   

 

 
 
 

R&G 

Unit 

1

, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ

 

Tel: +44 (0)

1

420 89007  Fax: +44 (0)

1

420 87301  

www.rg-racing.com

  Email: 

[email protected]

 

 

IMPORTANT: -

 WHEN FITTING THIS PRODUCT IT IS YOUR RESPONSIBILITY TO ENSURE THAT 

THE PRODUCT IN NO WAY IMPEDES THE OPERATION OF THE MOTORCYCLE AND IS CHECKED 
REGULARLY FOR TIGHTNESS AND OPERATION. 
 
FAILURE TO CHECK THE ABOVE COULD RESULT IN SERIOUS INJURY OR DAMAGE. 

 

ISSUE 1 - 15/07/2019 (FB) 

 

CONSUMER NOTICE 

The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design 

changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. 

The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other 

than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable q

uality and 

suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and 
care and rectify any fault free of charge unless the workmanship has been disturbed.  The Buyer is responsible for ensuring that 

the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its 

option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or 

used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if

 the 

defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death 

and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts 

paid by the Buyer for the Products or the fitting or service concerned. These terms do not 

affect the Buyer’s statutory rights.

 

 

R&G RACING RETURNS POLICY (NON-FAULTY GOODS) 

Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they 

were purchased direct from us (customer must prove if necessary).  Otherwise to be returned to original vendor. Goods must be 

in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the 

gross value exc. P&P 

 at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns 

of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to 

faulty goods. 

 

 

 

Summary of Contents for LGFK0023










Reviews: