R&G CLG0023CG/LH Fitting Instructions Manual Download Page 9

Page 

3

 of 

  

 

CLG0023CG/RH

   

 

   

 

 

 

R&G 

Unit 

1

, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ 

Tel: +44 (0)

1

420 89007  Fax: +44 (0)

1

420 87301  

www.rg-racing.com

  Email: 

[email protected]

 

 

CONSUMER NOTICE 

The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design 

changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. 

The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other 

than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality 

and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable 

skill and care and rectify any fault free of charge unless the workmanship has been disturbed.  The Buyer is responsible for 

ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products 

R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have 

been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good 

engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting 

its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability 

shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect 

the Buyer’s statutory rights. 

 

R&G RACING RETURNS POLICY (NON-FAULTY GOODS) 

Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if 

they were purchased direct from us (customer must prove if necessary).  Otherwise to be returned to original vendor. Goods 

must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% 

of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. 

No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does 

not refer to faulty goods. 

 

Summary of Contents for CLG0023CG/LH













Reviews: