Randell SSAC-40BSC, Operator'S Manual

Page: 13 / 20

unifiedbrands.net
13
C ontrol S ettings
Eliwell Setting in Order By Folder
X R 2 0 C E *
S S A C
Open Display
Purchased / Stock Part Number
Purchased part # RF CNT0501
Replacement part # RP CNT0601
Folder Code Yes Code
Set Thermostat set point 34 Set Set 33
Modifications (Shown in RED) Yes
C P
C o d e Locked Yes
DiF Thermostat Differential (hysterisis) 6 DiF HY 4 Set Thermostat set point 33
HSE Upper Set Point 45 HSE US 45 HY Thermostat Differential (hysterisis) 4
LSE Lower Set Point 32 LSE LS 32 LS Lower Set Point 32
Ont Compressor ON (probe failure) 8 Ont COn 8 US Upper Set Point 45
Oft Compressor OFF (probe failure) 2 Oft COF 4 Ot Offset Room Temp 7
dOn Output delay @ Startup (Compr) 0 dOn P 2 P 2nd Probe Present Y
dOF Anti-Cycle Time (min off after cycle) 1 dOF AC 1 O E Evaporator Probe Calibration 0
dbi Compr Start to Start Delay (min) 4 dbi O d S Output delay @ Startup 0
OdO Output delay @ Startup (All Relays) 0 OdO OdS 0 A C Anti-Cycle Time (min off after cycle) 1
d E F C O n Compressor ON time (probe failure) 8
dty Defrost Type 0 dty tdF C O F Compressor OFF (probe failure) 4
dit Interval between Defrosts 3 dit IdF 3 C F °C /°F F
dCt Defrost Count (0=CRT, 1=TT, 2=COT 1 dCt r E S Resolution 0.0°C (only °C) in
doh Start defrost delay 0 doh dSd d t E Defrost Termination Temp 43
dEt (Maximum) length of Defrost 25 dEt ndF 25 IdF Interval between Defrosts 3
dSt Defrost Termination Temp 43 dSt dtE 43 ndF (Maximum) length of Defrost 25
dPo First defrost at startup Y dPo dPo d F d Display during Defrost it
F a n d A d Max display delay after defrost 20
dt Drip time after defrost end 1 dt Fdt i 1 P Digitial Input Polarity CL
d i S d i d Digital Input Alarm Delay 5
LOC Locked y LOC Code Code
o d c Open Door Compressor Status no
PAI Password 0 PAI r E L Software Info -
ndt Decimal Point ndt rES P t b Software info -
CA1 Room Probe Calibrate (Offset Temp) 7 CA1 Ot 7
CA2 Evaporator Probe Calibration 0 CA2 OE 0
ddL Display during Defrost 1 ddL dFd it
dro °C /°F 1 dro CF F
C n F
HOO Probe Selection PTC / NTC 0 HOO PbC
H42 2nd Probe Present Y H42 P2P Y
rEL Software Info - rEL rEL -
tAb Software info - tAb Ptb -
F P r
UL Up Load to Copy Card UL
dL Down Load to Copy Card dL
Fr Erase Copy Card Fr
Randell / Dixell Settings In Order
RF CNT0501
RF CNT0601
Dixell Cross Reference Eliwell
S S A C - X X S C
Open Display Case
Randell Control Settings
Control with “fnc” button = E liwell Control = R F CNT0601