RAMSET Cobra Tool Operator'S Safety & Operating Instruction Manual Download Page 14

Page: 14 / 16

DISASSEMBLY

DISASSEMBLY
14

TOOL DISASSEMBLY

Rotate the barrel retention clip
off of the pawl using a flat blade
screwdriver or the point of a long
fastener.

Remove the pawl by lifting it up and
away from the tool body.

Slide the front barrel assembly out
of the tool body.

Unseat and remove the shear clip
by prying it up with a flat blade
screwdriver or fastener point.
Remove the clip from the barrel by
prying it up and away from the
groove in the barrel. Use care to
keep the clip from flying free when
it is removed.

Separate the front barrel and guide
from the rear barrel assembly

ROTATE THE BARREL RETEN-

TION CLIP AWAY FROM PAWL

REMOVE THE PAWL

REMOVE THE BARREL ASSEMBLY

REMOVE THE SHEAR CLIP

SEPARATE THE FRONT BARREL

FROM THE REAR BARREL

Summary of Contents for Cobra Tool

















Search results

Summary of Contents for Cobra Tool

Reviews:

Related manuals for Cobra Tool

Brands by name

Popular brands

RAMSET Cobra Tool, Operator'S Safety & Operating Instruction Manual

Search results

Summary of Contents for Cobra Tool

Reviews:

Related manuals for Cobra Tool

Brands by name

Popular brands