- 07 -
Hammer Drill / Driver 18V
Owners Manual
English |
15
Bosch Power Tools
1 609 92A 33F | (23.5.16)
16
Universal bit holder*
17
Rotational direction switch
18
On/Off switch
19
Handle (insulated gripping surface)
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Noise/Vibration Information
Sound emission values determined according to
EN
60745-2-1, EN
60745-2-2.
Wear hearing protection!
Cordless Drill/Driver
CBHDD18
Rated voltage
V=
18
No-load speed
–
1st gear
–
2nd gear
min
-1
min
-1
0–480
0–2100
Impact rate
min
-1
0–31500
Max. torque for soft screwdriving applica-
tion according to ISO 5393
Nm
47
*
Maximum torque, hard screwdriving appli-
cation according to ISO 5393
Nm
75
*
Maximum drilling diameter (1st/2nd gear)
–
Wood
–
Steel
–
Brickwork
mm
mm
mm
82
13
16
Tool holder
1.5 – 13
Max. screw dia.
mm
12
Weight according to EPTA-Procedure
01:2014
kg
2,3 - 2,8*
Permitted ambient temperature
–
during charging
–
during operation
**
and during storage
°C
°C
0... +45
-20... +50
Recommended batteries
CBBAT18...
Recommended chargers
CBCHR18
*depending on the battery pack being used
**
limited performance at temperatures <0
°C
OBJ_BUCH-2671-002.book Page 15 Monday, May 23, 2016 11:31 AM
14
| English
1 609 92A 33F | (23.5.16)
Bosch Power Tools
Service
Have your power tool serviced by
the Ramset
National
Service Centre
using only identical replacement parts.
This will en-sure that the safety of the power tool is
maintained.
Safety Warnings for Drills and Screwdrivers
Wear ear protectors when impact drilling.
Exposure to
noise can cause hearing loss.
Hold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
or fastener may contact hidden wiring.
Cutting accesso-
ry and fasteners contacting a “live” wire may make ex-
posed metal parts of the power tool “live” and could give
the operator an electric shock.
Use auxiliary handle(s), if supplied with the tool.
Loss
of control can cause personal injury.
Use appropriate detectors to determine if utility lines
are hidden in the work area or call the local utility com-
pany for assistance.
Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age.
Switch off the power tool immediately when the tool in-
sert jams. Be prepared for high reaction torque that
can cause kickback.
The tool insert jams when:
— the power tool is subject to overload or
— it becomes wedged in the workpiece.
Hold the machine with a firm grip.
High reaction torque
can briefly occur while driving in and loosening screws.
When working with the machine, always hold it firmly
with both hands and provide for a secure stance.
The
power tool is guided more secure with both hands.
Secure the workpiece.
A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Always wait until the machine has come to a complete
stop before placing it down.
The tool insert can jam and
lead to loss of control over the power tool.
Do not open the battery.
Danger of short-circuiting.
Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture.
Danger of explosion.
In case of damage and improper use of the battery, va-
pours may be emitted. Ventilate the area and seek
medical help in case of complaints.
The vapours can irri-
tate the respiratory system.
Use the battery only in conjunction with your
Ramset
power tool.
This measure alone protects the battery
against dangerous overload.
The battery can be damaged by pointed objects such as
nails or screwdrivers or by force applied externally.
An
internal short circuit can occur and the battery can burn,
smoke, explode or overheat.
The battery is supplied partially charged. To ensure full
battery capacity, completely charge the battery in the
battery charger before using for the first time.
Read the operating instructions of the battery charger.
Adjust the gear switch only when the machine is at a
complete stop.
Always push the gear selector and turn the operating
mode selector switch through to the stop.
Otherwise,
the machine can become damaged.
Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the centre
position.
Unintentional actuation of the On/Off switch can
lead to injuries.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions.
Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
The machine is intended for driving in and loosening screws
as well as for drilling in wood, metal, ceramics and plastic.
this
machine
is
additionally intended for impact drilling in
bricks, brickwork and masonry.
The light of this power tool is intended to illuminate the power
tool’s direct area of working operation and is not suitable for
household room illumination.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1
Tool holder
2
Keyless chuck
3
Depth stop
4
Auxiliary handle (insulated gripping surface)
5
Intermediate piece of auxiliary handle
6
Wing bolt for depth stop adjustment
7
Torque presetting ring
8
Mode selector switch
9
Gear selector
10
Colour clip
11
Belt clip
12
Battery pack
13
Battery unlocking button
14
Worklight
15
Overload protector indicator
OBJ_BUCH-2671-002.book Page 14 Monday, May 23, 2016 11:31 AM
