RAM 1500 2023 Page 134 Owner'S Manual Download

Page: 134 / 416

132

STARTING AND OPERATING

NOTE:

Do not attempt to make a shift while only the front or rear

wheels are spinning. This could cause damage to driveline

components.
When operating your vehicle in 4WD LOW, the engine

speed is approximately three times that of the 2WD or

4WD HIGH positions at a given road speed. Take care not

to overspeed the engine and do not exceed 25 mph

(40 km/h).
Proper operation of four-wheel drive vehicles depends on

tires of equal size, type and circumference on each wheel.

Any difference in tire size can cause damage to the

drivetrain.
Because four-wheel drive provides improved traction,

there is a tendency to exceed safe turning and stopping

speeds. Do not go faster than road conditions permit.

Shifting Procedure



If any of the requirements to select a new transfer case

position have not been met, then the transfer case will

not shift. The position indicator light for the previous

position will remain on and the newly selected position

indicator light will continue to flash until all the require

ments for the selected position have been met.



If all the requirements to select a new transfer case

position have been met, then the current position indi

cator light will turn off and the selected position indi

cator light will flash until the transfer case completes

the shift. When the shift is complete, the position indi

cator light for the selected position will stop flashing

and remain on.

IVE

-P

OSITION

LECTRONICALLY

HIFTED

RANSFER

ASE

—

QUIPPED

This is an electronic shift transfer case and is operated by

the 4WD Control Switch (Transfer Case Switch), which is

located on the instrument panel.

Five-Position/On-Demand Transfer Case

Five-Position/On-Demand Transfer Case — GT Models

This electronically shifted transfer case provides five

positions:



Two-Wheel Drive High Range (2WD) — This range is for

normal street and highway driving on dry hard surfaced

roads. Driving the vehicle in 2WD will have greater fuel

economy benefits as the front axle is not engaged in

2WD.



Four-Wheel Drive Automatic High Range (4WD AUTO) —

This range sends power to the front wheels automati

cally when the vehicle senses a loss of traction. This

range may be used during varying road conditions.



Four-Wheel Drive High Range (4WD HIGH) — This range

provides torque to the front driveshaft (engages

four-wheel drive) which allows front and rear wheels to

spin at the same speed. This provides additional trac

tion for loose or slippery road surfaces only.



Four-Wheel Drive Low Range (4WD LOW) — This range

provides low speed four-wheel drive. It maximizes

torque (increased torque over 4WD HIGH) to the front

driveshaft; allowing front and rear wheels to rotate at

the same speed. This range provides additional trac

tion and maximum pulling power for loose or slippery

road surfaces only. Do not exceed 25 mph (40 km/h)

in this range.



N (Neutral) — This range disengages both the front and

rear driveshafts from the powertrain. To be used for flat

towing behind another vehicle

page 187.

23_DT_OM_EN_USC_t.book Page 132

Summary of Contents for 1500 2023

































































































































































































































































































































































































































Search results

Summary of Contents for 1500 2023

Reviews:

Related manuals for 1500 2023

Brands by name

Popular brands

RAM 1500 2023, Owner'S Manual

Search results

Summary of Contents for 1500 2023

Reviews:

Related manuals for 1500 2023

Brands by name

Popular brands