Please note that Rajant warranty protection does not cover any damage caused by misuse of power
Please note that Rajant warranty protection does not cover any damage caused by misuse of power
supplies or by use of third-party power supplies.
supplies or by use of third-party power supplies.
Warning
Warning
In order to avoid sparking and possible damage to the unit, connect the powered Ethernet Output ca-
In order to avoid sparking and possible damage to the unit, connect the powered Ethernet Output ca-
ble to the BreadCrumb before applying power to the power supply.
ble to the BreadCrumb before applying power to the power supply.
Warning
Warning
To protect the user and the equipment against the risk of electric shock during high voltage transient
To protect the user and the equipment against the risk of electric shock during high voltage transient
events which may occur when this equipment or its antennas are installed outdoors, protective earth
events which may occur when this equipment or its antennas are installed outdoors, protective earth
grounding of the POE power supply is required. Case ground connections are provided on all Rajant
grounding of the POE power supply is required. Case ground connections are provided on all Rajant
supplied POE power supplies. The case ground connections must be used and must be connected to a
supplied POE power supplies. The case ground connections must be used and must be connected to a
protective earth ground. Protective earth grounding operations must be performed by trained person-
protective earth ground. Protective earth grounding operations must be performed by trained person-
nel, and according to local electrical codes and industry best practices, as well as Rajant’s own recom-
nel, and according to local electrical codes and industry best practices, as well as Rajant’s own recom-
mendations.
mendations.
For more information on physical installation, grounding, waterproofing connections, see
Installation
Guidelines
and the Appendix
Technical Bulletins
.
2.4.3 Ethernet Connector
The Ethernet port on the BreadCrumb ES1 enclosure is the female part of a Genesis Technology sealed
Ethernet connector. In a protected enviroment such as indoors or inside a 3rd party enclosure, a stand-
ard RJ45 male shielded cable may be connected to this port. Elsewhere, the correct sealed mating con-
nector must be used. The mating (male) part is Genesis Technology WAPV-100-AKY0T.
Figure: WAPV-1X00-AKY0T Sealed Ethernet Connector
Instructions for assembling the male sealed RJ45 connector on an unterminated shielded CAT5e or CAT6
Ethernet cable are found in the following Appendix:
Sealed RJ45 Assembly
.
Note: Premade Ethernet Cables
Note: Premade Ethernet Cables
Ethernet cables prebuilt with this connector may be purchased from Rajant (P/N: 06-1000068-030, ES1
Ethernet cables prebuilt with this connector may be purchased from Rajant (P/N: 06-1000068-030, ES1
cable, Ethernet, Cat5e shielded, Outdoor gland, 30ft).
cable, Ethernet, Cat5e shielded, Outdoor gland, 30ft).
2.5 M8 Connector
The BreadCrumb ES1 includes a 5-pin female M8 connector which provides pins to support one USB 2.0
interface and a physical Reset button (e.g. an LED Configuration / Zeroize Keys and Restore Factory De-
faults Switch).
The ES1 M8 connector is normally covered by a screw-in plastic protective cap. To remove the plastic M8
protective cap, unscrew it counter-clockwise. To re-install the M8 protective cap, screw it in clockwise.
Note
Note
Summary of Contents for BreadCrumb ES1
