background image

                                      

Beijing Raisecom Science & Technology Co., Ltd. 

2. Overview 

2.1. Introduction 

RC513/514 series remote-end managed, bandwidth adjustable Ethernet media 

converters are new generation media converters developed by Raisecom.   

The remote-end management means that the network administrators can manage both 

the host-end and the remote-end equipments to conduct such operations as working 

status review, equipment control, loop-back test, and data flow statistics, etc. 

The bandwidth adjustment means that the administrator can adjust the sending and 

receiving bandwidth of copper ports by N X 32kbps.   

Operations to host-end equipment are as follows:   

1.  Working status review of host-end equipment: 

The working status that can be reviewed is: 

a.  Copper port: upstream link, port ON/OFF, auto-sensing, full/half 

duplex; 

b. 

Fiber port: link receive (RLK), link transmit (TLK), port ON/OFF;   

c.  Others: Fault-pass-through enable/disable, management status of 

remote-end equipment, loop-back test status, loop-back test success report, 

configuration application.   

2.  Configuration of host-end equipment: 

The configurable items include:   

Copper port auto-negotiation, copper port duplex mode, copper port ON/OFF, 

Fault-pass-through enable/disable, remote-end management functions, reset of copper 

and fiber port, loop-back test enable and forbid, sending and receiving bit rate at N x 

32kbps.  

Operations to remote-end equipment are as follows:   

1. 

Working status review of remote-end equipment: 

The working status that can be reviewed is: 

a. 

Copper port:    link up, port ON/OFF, auto-sensing, full/half duplex; 

b. 

Fiber port: link receive (RLK), link transmit (TLK);   

c. 

Others: fault pass through enable, abnormal upper/lower limit of power 

voltage, feedback to configuration application, temperature of chassis 

ambience.  

2. 

Configuration of remote-end equipment: 

The configurable items include:   

Copper port auto-negotiation, copper port duplex mode, copper port ON/OFF, 

Fault-pass-through enable/disable, reset of copper and fiber port, sending and receiving 

bit rate at N*32kbps. 

 

 

 

 
 

3

Summary of Contents for RC513

















Reviews: