Raisecom RC3000-15 Page 65 Hardware Description Download

Page: 65 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

5 SDH cards

Raisecom Proprietary and Confidential

Table 5-5

Parameters of the Ethernet interface

Parameter

Description

Connector type

RJ45

Interface rate

10/100 Mbit/s auto-negotiation

Supported framelength

1536 bytes

Duplex mode

Full/Half duplex auto-negotiation

Flow control



Support IEEE 802.3x flow control in full duplex.



Support backpressure flow control in half duplex.

Wiring

Auto MDI/MDI-X

Compliant standard

IEEE 802.3x, IEEE 802.3u, IEEE 802.1Q, and MSAN-126

5.1.5 LEDs

Table 5-6 lists LEDs on the STM1 (B) card.

Table 5-6

LEDs on the STM1 (B) card

LED

Color

Description

PWR

Green

Power LED



Green: the power supply is normal.



Off: the power supply is abnormal.

SYS

Green

System status LED



Blinking green: the system is working properly.



Off: the system is working improperly.

ACT

Green

Primary/Slave LED



Green: when two STM1 cards are installed on the RC3000-15 (E),
this card is primary; when one STM1 card is installed on the
RC3000-15 (E), this LED keeps green.



Off: when two STM1 cards are installed on the RC3000-15 (E),
this card is slave.

LOS

Red

LOS alarm LED



Red: Loss of Signal (LOS) alarms are generated.



Off: no LOS alarms are generated.

LOF

Red

LOF alarm LED



Red: Loss of Frame (LOF) alarms are generated.



Off: input LOF alarms are generated.

LNK/A
CT

Green

Ethernet link LED



Green: Ethernet link interfaces are connected properly.



Off: Ethernet link interfaces are disconnected or are improperly
connected.



Blinking green: Ethernet link interfaces are receiving or sending
data.

Summary of Contents for RC3000-15


















































































































































































































































































Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands

Raisecom RC3000-15, Hardware Description

Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands