Raisecom P100R001 Hardware Description Download Page 50

Page: 50 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

4 DXC cards

Raisecom Proprietary and Confidential

4.1.2 Version

Card

Version

RC3000-15-DXC

F.00

4.1.3 Slots

Chassis version

Slot

E.30

7 and 8

4.1.4 Interfaces

Interface type

Table 4-1 Table 4-12 lists interfaces on the DXC (F.00) card.

Table 4-1

Interfaces on the DXC (F.00) card

Name

Type

Description

SNMP

RJ45

Network management interface –

NM-EXT

RJ45

Extended network management
interface

Manage the cascaded
RC3000-15 and
interconnect network
management channels
between cascaded
devices.

CONSOLE

RJ45

Console interface

–

ALMI/ALMO RJ45

On/Off value input/output
interface

2 ways of on/off value
input and 2 ways of
on/off value output

SYNC-RX

CC3 male
interface

2 MHz clock synchronization
input interface

Customized interface

SYNC-TX

CC3 male
interface

2 MHz clock synchronization
output interface

Customized interface

Interface parameter

Table 4-2 lists parameters of the SNMP interface.

Summary of Contents for P100R001


















































































































































































































































































Search results

Summary of Contents for P100R001

Reviews:

Related manuals for P100R001

Brands by name

Popular brands

Raisecom P100R001, Hardware Description

Search results

Summary of Contents for P100R001

Reviews:

Related manuals for P100R001

Brands by name

Popular brands