Raisecom P100R001 Hardware Description Download Page 173

Page: 173 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

10 Data cards

Raisecom Proprietary and Confidential

148

10.4.5 LEDs

Table 10-21 lists LEDs on the 8V35 card.

Table 10-21

LEDs on the 8V35 card

LED

Color

Description

PWR

Green

Power LED



Green: the power supply is normal.



Off: the power supply is abnormal.

SYS

Green

System status LED



Green: the system is working improperly.



Off: the system is working improperly.



Blinking green: the system is working properly.



TD1–TD8
(8V35)



TD1–TD4
(4V35H)

Green

Sending data LED



Blinking green: the corresponding channel is sending data.
The blinking frequency is related to the volume of data being
sent.



Off: the corresponding channel is not sending data.



RD1–RD8
(8V35)



RD1–RD4
(4V35H)

Green

Receiving data LED



Blinking green: the corresponding channel is receiving data.
The blinking frequency is related to the volume of data being
received.



Off: the corresponding channel is not receiving data.

10.4.6 DIP switch

Table 10-22 lists the DIP switch on the 8V35 card.

Table 10-22

DIP switch on the 8V35 card

SW1

Function

Status

Description

KEY1

Enter or quit
ISP mode.

Enter ISP mode. In this mode, the RC3000-15 is
waiting to be upgraded. You can upgrade MCU
program through the serial interface on the
backplane.

OFF

Enter normal working mode.

KEY2

Reserved

–



SW1 is in all OFF status before delivery, so the RC3000-15 can work properly.



After upgrade, J9 must be disconnected; otherwise, the RC3000-15 will
malfunction.

Table 10-23 lists the DIP switch on the 4V35H card.

Summary of Contents for P100R001


















































































































































































































































































Search results

Summary of Contents for P100R001

Reviews:

Related manuals for P100R001

Brands by name

Popular brands

Raisecom P100R001, Hardware Description

Search results

Summary of Contents for P100R001

Reviews:

Related manuals for P100R001

Brands by name

Popular brands