Raisecom P100R001 Hardware Description Download Page 159

Page: 159 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

10 Data cards

Raisecom Proprietary and Confidential

134

10.1.2 Version

Card

Version

RC3000-15-8ETHP

10.1.3 Slots

Chassis version

Slot

E.30 and E.20

1–6 and 9–13

10.1.4 Interfaces

Interface type

Table 10-1 lists interfaces on the 8ETHP card.

Table 10-1

Interfaces on the 8ETHP card

Name

Type

Description

1–8

RJ45

Corresponding to 8 ways of remote Ethernet services

Interface parameter

Table 10-2 lists parameters of the interface on the 8ETHP card.

Table 10-2

Parameters of the interface on the 8ETHP card

Parameter

Description

Interface type

RJ45

Interface rate

10/100 Mbit/s auto-negotiation

Duplex mode

Full/Half duplex auto-negotiation

MTU

2048 bytes

Flow control



Support IEEE 802.3x flow control in full duplex.



Support back pressure flow control in half duplex.

Wiring

Auto-MDI/MDIX

Compliant standard

IEEE 802.3x

Summary of Contents for P100R001


















































































































































































































































































Search results

Summary of Contents for P100R001

Reviews:

Related manuals for P100R001

Brands by name

Popular brands

Raisecom P100R001, Hardware Description

Search results

Summary of Contents for P100R001

Reviews:

Related manuals for P100R001

Brands by name

Popular brands