Raisecom iTN8600-I Product Description Download

Page: 31 / 71

Raisecom
iTN8600-I (A) Product Description

3 Cards and parts

Raisecom Proprietary and Confidential

Figure 3-3

Panel of the AC power supply

3.3.3 Functions

Table 3-12

Functions

Function

Description

Basic functions



Support wide voltage input range of 100–240 VAC



Support the maximum load of 175 W.

Protection
functions



Support dual power supply 1+1 protection.



Support dual power load balancing.



Support how swapping.

3.3.4 Interface

Table 3-13

Interface on the AC power supply

Print

Type

Description

–

C13 connector interface

Equipped with a power cable clip

3.3.5 LED

Table 3-14

LED on the AC power supply

Print

Color

Description

–

Green

Power LED



Green: the power supply is normal.



Off: the power supply is abnormal.

Summary of Contents for iTN8600-I








































































Search results

Summary of Contents for iTN8600-I

Reviews:

Related manuals for iTN8600-I

Brands by name

Popular brands

Raisecom iTN8600-I, Product Description

Search results

Summary of Contents for iTN8600-I

Reviews:

Related manuals for iTN8600-I

Brands by name

Popular brands