Raisecom ISCOM6820-GP Hardware Description Download Page 47 | Manualshive

Page: 47 / 61

background image

Raisecom
ISCOM6820-GP (A) Hardware Description

4 Pluggable optical modules

Raisecom Proprietary and Confidential

Copyright © Raisecom Technology Co., Ltd.

35

4

Pluggable optical modules

This chapter describes pluggable optical modules (Raisecom SFP modules are recommended)
that could be used by the ISCOM6820-GP, including the following sections:



1000 Mbit/s SFP optical module



10 Gbit/s SFP+ optical module



PON SFP optical module

4.1 1000 Mbit/s SFP optical module

4.1.1 Functions and appearance

The 1000 Mbit/s Small Form-factor Pluggables (SFP) optical module is applicable to the
1000 Mbit/s telecommunication or data communication networks. It is integrated with
sending and receiving features.

Figure 4-1 shows the appearance of the 1000 Mbit/s SFP optical module.

Figure 4-1

1000 Mbit/s SFP optical module

4.1.2 Label

There is a label on the bottom of the SFP optical module, which describes the model of the
SFP optical module, as shown in Figure 4-2.

«
...
45
46
47
48
49
...
»

Summary of Contents for ISCOM6820-GP






























































Reviews:

No comments

Related manuals for ISCOM6820-GP

Brand: GATT AUDIO Pages: 2

Brand: Blue Pages: 15

Brand: Immarsat Pages: 2

Brand: G.R.A.S. Pages: 17

Brand: D-Box Pages: 12

Brand: Comica Pages: 20

ETR 2000 series

Brand: Delco Pages: 34

Brand: Scott Pages: 13

Brand: Samson Pages: 8

Brand: MAJORITY Pages: 32

Brand: Senal Pages: 12

DIRECTREC DR-2000

Brand: Olympus Pages: 38

Brand: Speco Pages: 3

Brand: Panasonic Pages: 24

RS2135I - Compact Audio System

Brand: RCA Pages: 13

Brand: RCA Pages: 19

Brand: RCA Pages: 21

Brand: Craig Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands