Raisecom ISCOM6820-GP Hardware Description Download Page 50

Page: 50 / 61

Raisecom
ISCOM6820-GP (A) Hardware Description

4 Pluggable optical modules

Raisecom Proprietary and Confidential

Table 4-4

Technical specifications of the SFP+ optical interface

Parameter

Description

Connector

LC/PC

Optical interface properties

Depend on the SFP+ optical module.

Encoding type

64B/66B

Transmission rate

10 Gbit/s

Working mode

Full duplex

Table 4-5 lists technical specifications of the SFP+ optical module.

Table 4-5

Technical specifications of the SFP+ optical module

Model

wavelength

(nm)

Laser type

laser

optical

power

(dBm)

Min.

overload

point

(dBm)

Extinction

ratio (dB)

sensitivity

(dBm)

Transmiss

ion

distance

(km)

USFP+-192/M

850 (VCSEL) PIN

-8.2 to 1

4.5

-11.1

0.3

USFP+-192/S1

1310 (DFB)

-8.2 to 1

4.5

-14.4

4.3 PON SFP optical module

4.3.1 Functions and appearance

The PON SFP optical module can be applied to the PON system. It is integrated with sending
and receiving features.

Figure 4-4 shows the appearance of the PON SFP optical module.

Figure 4-4

PON SFP optical module

4.3.2 Standard

The GPON interface on the ISCOM6820-GP supports the optical module compliant with the
Class B+, Class C+, and Class C++ standard.

Summary of Contents for ISCOM6820-GP






























































Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands

Raisecom ISCOM6820-GP, Hardware Description

Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands