Raisecom ISCOM6820-GP Hardware Description Download

Page: 42 / 61

Raisecom
ISCOM6820-GP (A) Hardware Description

3 Fiber and cables

Raisecom Proprietary and Confidential

Table 3-8

PINs of the RJ45 Ethernet interface

PIN

Function

PIN

Function

PIN 1

PIN 5

GND

PIN 2

PIN 6

TxD

PIN 3

RxD

PIN 7

PIN 4

GND

PIN 8

3.4 DC power cable

3.4.1 Introduction

The DC power cable supplies -48 VDC power from the power souring equipment to the
power interface on the RPD1302 module of the ISCOM6820-GP, and then transmits power to
the entire device.

3.4.2 Appearance

The DC power cable is composed of the DC power connector and coaxial cable, as shown in
Figure 3-9.

Figure 3-9

DC power cable

3.4.3 Technical specifications

Table 3-9 lists technical specifications of the DC power cable.

Table 3-9

Technical specifications of the DC power cable

Parameter

Description

Name

POL-DC(2C)-DSUB/U-6.0mm

-D/RoHS

Connector A

DSUB power connector-weld line-3 core (hole + pin + hole)

Positive wire

60227 IEC 02 (RV) red (6mm

) with flame retardant tube

Negative wire

60228 IEC 02 (RV) black (6mm

) with flame retardant tube

Rated voltage (V)

450/750

Insulation and voltage
resistance (cable)

2500 VAC, 5min

Summary of Contents for ISCOM6820-GP






























































Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands

Raisecom ISCOM6820-GP, Hardware Description

Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands