Raisecom ISCOM2008 User Manual Download Page 5

Page: 5 / 17

Preface

About This Manual

This manual is for users of ISCOM2008 series switches with hardware version higher than VER

B.00.

Who Should Read This Manual

This manual is a reference for device installation and maintenance staff.

Relevant Manuals

《

ISCOM2008 Series Switches Commands Notebook

》

《

ISCOM2008 Series Switches Configuration Guide

》

Organization

Chapter 1: Overview

This chapter introduces the content of the manual and explains relevant term definitions.

Chapter 2: Specifications and Dimension

This chapter is an instruction of the device specifications, device dimension and device operating

environment.

Chapter 3: Device Appearance

This chapter describes the panel of the device and the definition of the indicators on the device panel.

Chapter 4: Installation and Application

This chapter introduces the cables and subcards that may be applied during the installation process.

Chapter 5: Notes

This chapter explains other detailed requirements that must be satisfied during the installation.

Summary of Contents for ISCOM2008


















Search results

Summary of Contents for ISCOM2008

Reviews:

Related manuals for ISCOM2008

Brands by name

Popular brands

Raisecom ISCOM2008, User Manual

Search results

Summary of Contents for ISCOM2008

Reviews:

Related manuals for ISCOM2008

Brands by name

Popular brands