background image

RAISCUBE FDM 3D Printer 

1.4

 

Cura 3D Printing Slicing Configuration. 

 

 

 

 

 

“Layer height”  is the most 

important setting to 
determine the quality of 

your print. Normal quality 
prints are 0.2mm, high 

quality is 0.1 or 0.05mm.  

Shell Thickness: Thickness of the 

outside shell in the horizontal 
direction.This is used in 

combination with the nozzle size to 
define the number of perimeter 

lines and the thickness of those 
perimeter lines. 

Retract the filament when the nozzle 
is moving over a none-printed area. 

Details about the retraction can be 

configured in the advanced tab. 

This controls the thickness of 

the bottom and top layers, 
the amount of solid layers 

put down is calculated by the 
layer thickness and this 

value.Having this value a 
multiple of the layer 

thickness makes sense. And 

keep it near your wall 
thickness to make an evenly 

strong part. 

This controls how densely filled 
the insides of your print will be. 

For a solid part use 100%, for an 

empty part use 0%. A value 
around 20% is usually enough. 

This won't affect the outside of 
the print and only adjusts how 

strong the part becomes. 

Est Printing Time. 

Save file. 

Open File. 

Layer 

View. 

Speed at which printing happens. A 
well adjusted Ultimaker can reach 
150mm/s, but for good quality prints 
you want to print slower. Printing 

speed depends on a lot of factors. So 

you will be experimenting with optimal 
settings for this. 

Printing Temperature used for 
printing. Set at 0 to pre-heat 

yourself.For PLA a value of 
210

 is usually used.For ABS a 

value of 230

 or higher is 

required. Bed Temperature is 

used for the heated printer bed. 

Set at 0 to pre-heat yourself. 

Type of support structure 

build. Touching buildplate 
is the most commonly used 

support setting.None does 
not do any 

support.Touching 

buildplate only creates 
support where the support 

structure will touch the 
build platform.Everywhere 

creates support even on 
top of parts of the model. 

Different options that help in 

preventing corners from lifting 

due to warping.Brim adds a 
single layer thick flat area 

around your object which is 
easy to cut off afterwards, and 

it is the recommended option. 

Raft adds a thick raster below 
the object and a thin interface 

between this and your 
object.(Note that enabling the 
brim or raft disables the skirt) 

Diameter – Filament Diameter 
(e.g 1.75mm);Flow--Flow 

compensation, the amount of 
material extruded is multiplied by 

this value. 
Nozzle Size(mm) – 0.4mm. 

Summary of Contents for R2













Reviews: