28
CAPACITY AND SALT SETTINGS
THE SYSTEM SHOULD BE INSTALLED IN AN AREA NOT AFFECTED
BY EXTREME HEAT, COLD, OR THE ELEMENTS.
THIS SYSTEM MUST BE INSTALLED IN ACCORDANCE WITH ALL
APPLICABLE STATE AND LOCAL LAWS AND REGULATIONS.
DO NOT INSTALL SYSTEM WHERE WATER IS MICROBIOLOGI-
CALLY UNSAFE OR OF UNKNOWN QUALITY WITHOUT ADEQUATE
DISINFECTION BEFORE OR AFTER THE SYSTEM.
THE SYSTEM CONTAINS AN ION-EXCHANGE MEDIA FOR
REMOVING LISTED CONTAMINANTS AND MUST BE REGENER-
ATED PERIODICALLY. PLEASE REFER TO THE OWNERS MANUAL
TO DETERMINE THE FREQUENCY OF REGENERATIONS.
PLAIN, WHITE BLOCK SALT IS RECOMMENDED FOR THIS
SYSTEM. IF BLOCK SALT IS NOT AVAILABLE, A CLEAN, COARSE
OR EXTRA COARSE ROCK OR SOLAR SALT MAY BE USED. DO
NOT USE GRANULATED SALT. CONSULT YOUR RAINSOFT DEALER
FOR POTASSIUM CHLORIDE USE.
YOUR LOCAL DEALER IS AVAILABLE FOR SERVICE AND
WARRANTY PART REPLACEMENTS.
STATE OF CALIFORNIA DEPARTMENT OF HEALTH SERVICES
CERTIFICATE NUMBER 06-1805
TESTED AND CERTIFIED BY THE WQA TO
NSF/ANSI STANDARD 44 FOR THE SPECIFIC
PERFORMANCE CLAIMS AS VERIFIED AND
SUBSTANTIATED BY TEST DATA
SEE THE OWNERS MANUAL FOR GENERAL
OPERATION AND MAINTENANCE REQUIREMENTS.
SEE WARRANTY CARD FOR SPECIFIC WARRANTY
INFORMATION.
IMPORTANT NOTICE
READ THIS PERFORMANCE DATA SHEET AND COMPARE
THE CAPABILITIES OF THIS UNIT WITH YOUR ACTUAL
WATER TREATMENT NEEDS. IT IS RECOMMENDED THAT
BEFORE PURCHASING A WATER TREATMENT UNIT, YOU
HAVE YOUR WATER SUPPLY TESTED TO DETERMINE YOUR
ACTUAL WATER TREATMENT NEEDS.
· SERVICE FLOW RATE = 9.5 GPM (36.0 LPM)
· DRAIN FLOW RATE: 2.0 GPM (7.6 LPM)
· PSI DROP @ FLOW RATE: 10.0 psi (0.7 kgf/cm2)
· OPERATING PSI OF SUPPLY: 20 psi - 120 psi
(1.47 - 8.45 kgf/cm2)
· OPERATING TEMPERATURE: 40° F - 100° F
(4.4° C - 38° C)
· ELECTRICAL: 24 VAC, 50/60 Hz (COMPUTER)
· SALT PER REGENERATION: VARIABLE
· EFFICIENCY: 4,470 GRAINS/LBS. SALT @
2.4 LBS. DOSAGE
LIST OF CONTAMINANTS REDUCED
CAPACITY
SALT
10,700 GRAINS
@ 2.4 LBS. OF SALT
19,200 GRAINS
@ 6.0 LBS. OF SALT
22,500 GRAINS
@ 9.0 LBS. OF SALT
*HARDNESS WAS USED AS A SURROGATE FOR BARIUM AND RADIUM REDUCTION CLAIMS PER NSF/ANSI
STANDARD 44.
ADDITIONAL NOTES
• THE LIST OF SUBSTANCES WHICH THIS TREATMENT DEVICE REDUCES DOES NOT NECESSARILY MEAN THAT THESE
SUBSTANCES ARE PRESENT IN YOUR WATER SUPPLY.
• ACTUAL RESULTS MAY VARY DUE TO LOCAL WATER CONDITIONS.
• AN EFFICIENCY RATED WATER SOFTENER IS A DEMAND INITIATED REGENERATION SOFTENER, WHICH ALSO
COMPLIES WITH SPECIFIC PERFORMANCE SPECIFICATIONS INTENDED TO MINIMIZE THE AMOUNT OF REGEN-
ERATE BRINE AND WATER USED IN ITS OPERATION AND WILL ACHIEVE A RATING OF NOT LESS THAN 3,350
GRAINS OF TOTAL HARDNESS EXCHANGE PER POUND OF SODIUM CHLORIDE SALT AND SHALL NOT DELIVER MORE
SALT THAN ITS LISTED RATING. THE EFFICIENCY IS MEASURED BY A LABORATORY TEST DESCRIBED IN NSF/ANSI
44. THE TEST REPRESENTS THE MAXIMUM POSSIBLE EFFICIENCY THAT THE SYSTEM CAN ACHIEVE. OPERATIONAL
EFFICIENCY IS THE ACTUAL EFFICIENCY ACHIEVED AFTER THE SYSTEM HAS BEEN INSTALLED AND IS TYPICALLY
LESS THAN THE TESTED EFFICIENCY DUE TO INDIVIDUAL APPLICATION FACTORS INCLUDING WATER HARDNESS,
WATER USAGE, AND OTHER CONTAMINANTS THAT REDUCE THE SOFTENERS CAPACITY.
• A WATER SOFTENER IS NOT INTENDED TO BE USED FOR TREATING WATER THAT IS MICROBIOLOGICALLY UNSAFE
OR OF UNKNOWN QUALITY WITHOUT ADEQUATE DISINFECTION BEFORE AND AFTER THE SYSTEM.
• EFFICIENCY OF THE CONDITIONER IS VALID ONLY AT THE STATED SALT DOSAGE.
CONTAMINANT
USEPA
MCL
BARIUM*
2 PPM
RADIUM 226/228*
5 PCI/L
NSF/ANSI STANDARD 44 TEST CONDITIONS: 35 ± 5 psi, 65 ± 10°F, pH 7.5 ± 0.5 at service flow rate
CHALLENGE
AVERAGE INFLUENT LEVEL
AVERAGE EFFLUENT LEVEL
HARDNESS
350 PPM
9 PPM
SOFTENING PERFORMANCE TEST
NSF/ANSI STANDARD 44 TEST CONDITIONS: 35 ± 5 psi, 65 ± 10°F, pH 7.5 ± 0.5 at service flow rate
DEMAND INITIATED
WATER TREATMENT SYSTEM
CALIFORNIA
PERFORMANCE DATA SHEET
Page 1 of 2
EC4-CAB 60 CV
DEMAND INITIATED TREATMENT SYSTEM
