background image

19 

 

Warranty Terms and Conditions

 

KW 4V8

 
With this consumer warranty RAC GmbH & Co. KG in Bad Rappenau, Germany, ensures on the product, starting 
from the time of the first use and/or the first installation by the authorized specialized trade, a two-year materials 
and labor warranty.  
 
The warranty is exclusively limited to free substitution of defective parts, whose cause is faulty construction or 
material defects, as well as to the warranty repair. 
 
A warranty claim does not exist if defects resulted from inappropriate assembly, transport damage, mechanical 
damage, or foreign interference.  
 
Accidents, forces of nature or other causes which can be answered for, in particular water and fire, are not subject 
to the guaranteeing of Rainbow®. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Version: MSJ/1.2 - 04/06 

 

This document is protected by copyright. Any duplication, including printing , in whole or part , and all reproductions of 

diagrams, also in a modified version, is permissible only with the written permission of Rainbow. 

Copyright © 2005 by RAC GmbH & Co. KG. Rainbow is a registered trademark. 

Summary of Contents for KW 4V8




















Reviews: