Raider RDP-BS07, User Manual

Page: 12 / 68

12 www.raider.bg
Level A of the generated noise is usually: sound
pressure level Lp
A
= 91 dB (A); power of sound Lw
A
= 103 dB (A). Uncertainty K = 3 dB. Work with a
silencer! The resultant value of vibration (the vector
sum of the three directions) is determined according
to EN 60745. Value of the generated vibrations ah
= 4,16 m/s
2
, uncertainty K = 1,5 m/s
2
. That in this
operating manual value for vibration is measured by
the method specified in EN 60,745 and can be used to
compare different power. The level of vibration varies
depending on the specific activity carried out and in
some cases may exceed that in this guide value. For
an exact estimate of the burden of vibrations in a
working cycle should be recorded and the intervals in
which the power is off or idling. This can significantly
reduce the reporting burden of vibrations throughout
the business cycle.
8. Preparing for the job. Installation of auxiliary
accessories and consumables.
8.1. Prahoulovitelna bag.
In the current activities you can use prahoulovitelna
bag. Insert the nozzle of the bag firmly on the nozzle
opening for outgoing air stream (6). To operate dust-
extraction effectively empty prahoulovitelnata bag
promptly. In continuous operation a system of dust-
extraction with an additional prahodmukachka.
8.2. Installing and / or replacement of the strip
sandpaper.
Dissolve the locking lever (7) end. Thus the tape
sandpaper (4) is released and can be removed. Insert
a new tape sandpaper (4). In this careful direction of
the arrows inside the strip and body-power to match.
Again, back locking lever (7) in the starting position.
9. Inclusion and exclusion.
Beware of the voltage of supply network! Tension
of the supply network must comply with the details
shown on the plate of power. Appliances marked with
230V, can be supplied with a voltage of 220V.
9.1. To turn the band grind, press and hold the
trigger switch (1). For locking of pressed starting
switch (1) press (2). Exclusion power release trigger
switch (1), respectively, if anchored to the button (2),
first press the short term and then release the trigger
switch (1).
9.2. Adjust the position of the grinding belt
(adjustment of the parallelism of the axes of the guide
rollers).
Include grind. When the grinding belt is moving,
rotate vartoka adjustment of grinding tape (5), so
that the grinding bar to rotate evenly without depart
from the rolls. Assuming grinding bar to move
progressively towards to the body of grinding (which
means that the axes of the rollers are not parallel) bar
will quickly exports.
10. Working with the band grind.
Where possible, work with small force of
constriction to increase the durability of the tape.
The mass of the power is sufficient to achieve good
performance. Excessive increases the power of the
press does not increase productivity but leads to
intensive wear of tools and tape sandpaper.
Grind parallel to the fiber cross-grinding leads to
the formation of traces of scratches and undesirable
effects.
Keep and refer to the accessories carefully.
Make periodic breaks at work.
Do not throw the tool and do not overload.
11. Service and Support.
11.1. Never use water or any chemical liquid to
clean the band grind. It should be cleaned with a
piece of dry tissue, and accumulated dust removed
with a soft brush. Always keep grinding dry place and
keep the vent on the hull clean.
11.2. Replacing the carbon brushes. Exports
(shorter than 5 mm), up or broken carbon brushes of
the engine should be replaced. Always replace both
the two brushes. Work on replacement of carbon
brushes entrusted only to qualified person with
original spare parts in company service of RAIDER.
11.3. The repair of your power is best carried out
only by qualified professionals repairers of RAIDER,
which used only original spare parts. Thus ensuring
their safe operation.
12. Preservation of the environment.
In view of environmental power, additional
accessories and packaging must be subjected to
appropriate processing for reuse of the information
contained in these materials.
Do not dispose of electric household waste! Under
the EU Directive 2012/19/EC on scrapped electrical
and electronic devices and the establishment and
national law power which can be used more, must be
collected separately and be subjected to appropriate
processing for recovery of contained therein scrap.