15
off the power of power. Put the key in one
of the open side of the chuck. Dissolving
the jaws to the desired size and place
in the drill chuck. With key-locking in
three successive drill a hole in the chuck.
We must always remember that the key
should be removed from the drill after
the completion of operations related
to installation and dismantling of the
drill. When mounting a new drill should
be checked by the inclusion of a short
drill, drill that rotates in an axis without
“flicker”. This will help us make sure that
it is not distorted.
8.4. Inclusion and exclusion. Beware
of the voltage of supply network! Supply
voltage of the network must conform to
the details shown on the plate of power.
Appliances marked with 230 V, can be
supplied with a voltage of 220 V.
8.5. To turn the drill press and hold
the trigger switch (1). For locking of
the starting switch pressed (1) press (3).
Exclusion relax power trigger switch (1),
respectively, if anchored to the button (3),
first press the short term and then release
the trigger switch (1).
8.6. Adjust the speed of rotation. Drill
allows to work with different speed of
spindle. Alignment is done using the
position (2). In the range of each setting
a speed can be adjusted smoothly by
increasing speed and reducing pressure
on the trigger button (1). Turn right
speed regulator (2) leads to increase their
rotation and left to decrease.
8.7. Correct choice of the rate of speed
shall be held where drill is included
without load. So speed-minded when
working with a load may be lower.
8.8. Hammer drilling.
Place the switch (6) the symbol
“hammer drilling.” Switch (6) falls in the
correct position with a distinct twinge.
8.9. Tools to develop or cornering.
Turntable working instrument can be
bent. After continuous operation with low-
speed power to cool as to leave it idling for
approximately 3 minutes with a maximum
speed of rotation. When working with
terminals must always use a universal
extension. Use only the cores that are
suitable for heads of screws. Turning to
always place the switch “drilling / hammer
drilling» (6) in position «Drilling».
8.10. Select the direction of rotation.
With the switch (4) you can change the
direction of rotation of power. Rotate
right: For drilling and turning the screw
press to switch the direction of rotation
(4) at point blank range left. Rotate left:
To develop the screws and nuts, press
switch direction of rotation (4) right to the
point blank range. Switch (6) the choice of
operation should be in position «Drilling».
It must be done to change the direction of
rotation when the spindle rotates a drill!
8.11. Not used in rotation to the left
mode of attack.
8.12. When you need to vent large
diameter, is recommended first to break a
small opening, which will then be drilling
to the desired size. This will prevent
overloading the drill. Drilling deep holes
should be done gradually, as periodically
removed from the drill hole to remove chips
or dust. If during drilling to drill block up
in holes, you should exclude drill. Use a
change of direction of rotation to remove
the drill from the hole. Drill must be kept
in alignment with the hole. Ideally, the
drill should be placed perpendicular to the
surface of the material being processed. If
the condition for perpendicularity is not
respected at work can lead to trapped
or breakage in drill hole and injury to
the user. Continued drilling at low speed
the engine from overheating threatens.
Must make periodic breaks during work
or to allow the drill to work on no-load
maximum speed for about 3 minutes. Do
not obscure the openings in the hull used
for ventilation of the engine.
8.13. Outdoor use.
Connect the machine only in
installations equipped with electric switch
Fi (safety shut-off switch with Residual
protection RCD Residual Current Device.
RCD must be no more than 30 mA).
Make periodic breaks at work.
Keep and refer to the accessories
carefully.
Do not throw the tool, do not overload,
do not soak in water and other liquids
do not use it for mixing adhesives and
concrete coatings.
9. Service and support.
9.1. Impact drill does not require
