background image

RadioLink Electronic Ltd

www.radiolink.com

Thanks for purchasing RadioLink 8-channel dual antenna receiver R8F.
To fully enjoy the benefits of this product and ensure safety, please read the introduction carefully and set
up the device as instructed steps.
If any problems found during the operation process, please kindly refer to the manual first. Then you
could contact our distributors to find solution or follow our Facebook homepage

https://www.facebook.com/RadioLink-1455452961436694/

to search related key words. Also you can

send your questions to

[email protected]

or

[email protected]

and we will

answer your question at the earliest.
Due to unforeseen changes in production procedures, the information contained in this manual is subject
to change without notice.
For more information please check our website

http://www.radioLink.com.cn

and follow our Facebook

and Youtube homepage.

SAFETY PRECAUTIONS

Never operate your model during adverse weather conditions. Poor visibility can cause
disorientation and loss of control of your model.

Never use this product in a crowd and illegal area.

Always ensure the trim levers at 0 and battery properly charged before connecting the receiver.

Always check all servos and their connections prior to each run.

Always be sure about turning off the receiver before the transmitter.

WARNING

This product is not a toy and is

NOT

suitable for children under the age of 18. Adults should keep the

product out of the reach of children and exercise caution when operating this product in the presence of
children.

Water or moisture may enter the transmitter inside through gaps in the antenna or joystick and cause

model instability, even out of control. If running in the wet weather(such as game) is inevitable, always
use plastic bags or waterproof cloth to cover the transmitter.

Summary of Contents for R8F









Reviews: