Radio Shack PRO-67 Operation Download Page 26

Page: 26 / 32

The recommended DC adapter supplies 9 volts and delivers at least

300 milliamps. It has a barrel plug with a center tip that can be set

to negative and correctly fits the scanner's POWER Jack. Using an

adapter that does not meet these specifications could damage the

scanner or the adapter.

To protect your vehicle's electrical system, always plug the adapter

into the scanner before you plug it into your vehicle's

cigarette-lighter socket. Always unplug the adapter from the

vehicle's cigarette-lighter socket before you unplug it from the

scanner.

If batteries are installed, make sure the battery switch inside the

battery compartment is set to the correct position.

1. Turn VOLUME/OFF counterclockwise until it clicks to make sure power is

turned off.

2. Set the adapter's voltage switch to 9V.

3. Connect the 3.4 mm outer diameter/1.3 mm inner diameter tip to the

adapter cord matching TIP to -.

4. Plug the adapter's barrel plug into your scanner's POWER jack.

5. Plug the other end of the adapter into your vehicle's

cigarette-lighter socket.

If you have installed rechargeable batteries and set

ALKALINE <- JACK -> NI-CD to NI-CD, the adapter powers the

scanner and recharges the batteries at the same time.

Note:

If the scanner does not operate properly when you use a DC adapter,

unplug the adapter from the cigarette-lighter socket and clean the

socket to remove ashes and debris.

CONNECTING THE ANTENNA

Follow these steps to attach the supplied flexible antenna to the

connector on the top of your scanner.

1. Align the slots around the antenna's connector with the tabs on the

scanner's BNC connector.

2. Slide the antenna's connector down over the scanner's connector and

rotate the antenna connector's outer ring clockwise until it locks

into place.

Connecting an Optional Antenna

The scanner's BNC connector makes it easy to connect a variety of

optional antennas (such as an external mobile antenna or outdoor base

station antenna). Your local Radio Shack store sells a variety of

antennas.

Summary of Contents for PRO-67

































Search results

Summary of Contents for PRO-67

Reviews:

Related manuals for PRO-67

Brands by name

Popular brands

Radio Shack PRO-67, Operation

Search results

Summary of Contents for PRO-67

Reviews:

Related manuals for PRO-67

Brands by name

Popular brands