background image

22

If you still have problems, disconnect the phone. If other phones on the same line
work properly, the fault is in this phone or its installation. If you cannot find the prob-
lem, take your phone to your local Radio Shack store for assistance.

The phone does not work or works 
poorly.

Be sure the base’s phone line cord and
AC adapter are correctly and securely
connected.

The handset battery pack does not 
charge.

Check the charging contacts on the
handset and base. If they are dirty,
clean them with a pencil eraser.

Handset doesn’t ring or receive a 
page.

• The battery pack might be weak. 

Charge the battery pack on the 
base for 15-24 hours.

• Be sure the handset’s ringer is 

turned on.

• Adjust the base’s antenna so it 

stands straight up.

• Move closer to the base.

• Move the base away from noise 

sources.

• Return the handset to the base to 

reset it.

The handset stops working or works 
poorly during a call.

• Move the handset closer to the 

base.

• Change channels.

• Be sure the handset’s battery pack 

is charged. (If the battery pack 
power is too low, it does not have 
enough power to light the PRI-
VACY/LOW BAT indicator.)

• Adjust the base’s antenna so it 

stands straight up

Problem

Solution

43-1083.fm  Page 22  Tuesday, August 17, 1999  2:17 PM

Summary of Contents for ET-908





























Reviews: