background image

7

3. Route the other end of the short

cord through the hole in the
bracket’s center.

4. Attach the supplied bracket to the

bottom of the base by inserting
the tabs on the bracket into the
slots on the base, then sliding the
bracket up.

5. Insert the supplied AC adapter’s

barrel plug into the 

12VDC

 jack on

the back of the base. Then plug
the adapter into a standard AC
outlet.

6. Plug the modular cord into the

wall plate’s jack.

7. Align the bracket’s keyhole slots

with the wall plate studs and slide
the base downward to secure it.

8. Carefully place the handset in the

cradle at the top of the base and
make sure it is secure.

Note: If you later want to mount
the base on a desktop, press

PUSH

 on the bracket and pull it off

to remove it.

9. Fully extend the base’s antenna

and place it in a vertical position.

Mounting the Base Directly 
on the Wall

You need two wood screws (not sup-
plied) for this mounting method.

1. Drill two holes 3

15

/

16

 inches apart.

Then thread a screw into each
hole, letting the heads extend 

1

/

4

inch from the wall.

43-1031.fm  Page 7  Tuesday, August 17, 1999  9:24 AM

Summary of Contents for ET-531





















Reviews: