Radio Shack ET-148 Owner'S Manual Download Page 9

Page: 9 / 16

SETTING THE DIALING
MODE

Set

MODE

on the back of the base for

the type of service you have (tone or
pulse). If you are not sure which type
you have, do this test.

1. Set

MODE

TONE

2. Lift the handset and listen for a dial

tone.

3. Press any number other than

Note: If your phone system requires
that you dial an access code (

, for

example) before you dial an outside
number, do not press the access
code either.

4. If the dial tone stops, you have

touch-tone service. Leave

MODE

set

TONE

If the dial tone continues, you have
pulse service. Set

MODE

PULSE

SETTING THE RINGER
SWITCH

Set

RINGER

on the back of the tele-

phone to select the desired ringer vol-
ume:

— Normal ringer volume.

— Reduced ringer volume.

OFF

— The telephone does not ring

Note: With the phone’s ringer off, you
can still make calls using the ET-148.
You can also receive calls if you hear an-
other telephone on the same line ringing.

43-637.fm Page 9 Friday, August 13, 1999 10:45 AM

Summary of Contents for ET-148

















Search results

Summary of Contents for ET-148

Reviews:

Related manuals for ET-148

Brands by name

Popular brands

Radio Shack ET-148, Owner'S Manual

Search results

Summary of Contents for ET-148

Reviews:

Related manuals for ET-148

Brands by name

Popular brands