background image

2

Important Information

ˆ

Important Information

FCC DECLARATION OF 
CONFORMITY

This device complies with Part 15 of the 

FCC Rules.

Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference re-

WARNING: To reduce the risk of fire or shock hazard, do not expose this 
product to rain or moisture.

CAUTION

RISK OF ELECTRIC SHOCK. 
DO NOT OPEN.

CAUTION:

 TO REDUCE THE RISK OF ELECTRIC SHOCK, DO 

NOT REMOVE COVER OR BACK. NO USER-SERVICEABLE PARTS 
INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

This symbol is intended to alert you to the presence of 
uninsulated dangerous voltage within the product’s 
enclosure that might be of sufficient magnitude to con-
stitute a risk of electric shock. Do not open the product’s 
case.

This symbol is intended to inform you that important 
operating and maintenance instructions are included in 
the literature accompanying this product.

!

!

©

 2000 RadioShack Corporation. All Rights Reserved. 

RadioShack and RadioShack.com are trademarks

used by RadioShack Corporation.

63-1110.fm  Page 2  Friday, September 22, 2000  3:33 PM

Summary of Contents for 63-1110 - Wireless Mail Guard

















Reviews: