background image

11

keys on the transceiver. Hold down 

MON/FUNC

 then press 

LOCK/PTT

 to 

lock or unlock these keys. When these 
keys are locked, 

/2&.

/2&.

/2&.

/2&.

 appears. If the 

key tone is on, an error tone sounds 
when you press any of the keys.

SETTING THE 
COURTESY TONE

While turning on the transceiver, hold 
down 

LOCK/PTT 

to turn the courtesy 

tone on or off. When you turn on the 
courtesy tone, a tone sounds and 

&

0

&

0

&

0

&

0

721(

721(

721(

721(

 appears. When you end the 

transmission, the party you are 
communicating with hears the courtesy 
tone.

RESETTING THE 
TRANSCEIVER

If the transceiver stops operating 
properly, reset the transceiver by 
holding down 

QUIET/Q-SCAN

 while 

turning on the transceiver. All the set 
channels will be cleared. The current 
channel and the DW channel will be 
channel 0, Quiet Code will be off, and 
the key tone and courtesy tone will be 
on.

CARE

Keep the transceiver dry; if it gets wet, 
wipe it dry immediately. Use and store 
the transceiver only in normal 
temperature environments. Handle the 
transceiver carefully; do not drop it. 
Keep the transceiver away from dust 
and dirt, and wipe it with a damp cloth 
occasionally to keep it looking new.

Modifying or tampering with the 
transceiver’s internal components can 
cause malfunction and invalidate its 
warranty. If your transceiver is not 
performing as it should, take it to your 
local RadioShack store for assistance.

ˆ

Specifications

Operation Channels  .................................................................................................  GMRS: 7

                                                                 Interstitial: 7

                                                              Emergency: 1

Weather Channels ............................................................................................................... 10

Power Source ................................................................  8.4V, 1300mAH Ni-MH Battery Pack

12V, 200mA AC/DC Charger

Sensitivity at 12dB SINAD .............................................................................................  0.5uV

Adjacent Channel Rejection  ...........................................................................................  45dB

Audio Distortion  .................................................................................................................  7%

Output Power  ........................................................................................... 1W/5W @ 8.4V DC

Summary of Contents for 5W














Reviews: