background image

10

To monitor the DW channel and one 
operation channel:

 

1. Press /  

or /

SKIP

 to select a 

second channel.

2. Press 

DUAL

'8$/

'8$/

'8$/

'8$/

 appears. The 

transceiver checks the two 
channels alternately, and their 
numbers alternately appear. 
When a signal is received on 
either channel, the transceiver 
stops on the active channel until 
the signal disappears. After a few 
seconds of inactivity, dual watch 
mode resumes. 

3. Press any key to stop dual watch. 

To monitor one operation channel and 
one weather channel:

1. Press /  

or /

SKIP

 to select 

an operation channel. 

2. Press 

WX

 to turn on the weather 

radio. 

:;

:;

:;

:;

 appears.

3. Press /  

or /

SKIP

 to select a 

weather channel. 

4. Press 

DUAL

'8$/

'8$/

'8$/

'8$/

 appears. The 

transceiver checks the two 
channels alternately, and their 
numbers alternately appear. 

When a weather alert signal is 
received, the transceiver exits 
dual watch mode to receive the 
broadcast.

Note: To return to dual watch, 
press 

DUAL

.

When a signal is received on the 
operation channel, the transceiver 
stops on the active channel until 
the signal disappears. After a few 
seconds of inactivity, dual watch 
mode resumes. 

5. Press any key to stop dual watch.

SETTING THE KEY TONE

Hold down 

MON/FUNC 

then press 

/  

to set the key tone beep to on or off. 

 

appears when the key tone is on.

Note: The key tone does not beep 
when you press 

LOCK/PTT

 or 

MON/

FUNC

, even if the key tone is on.

USING APO/HI/LO

Press 

APO/HI/LO

 to set the transmitting 

power to high for long distance 
transmissions, or low for short distance 
transmissions. 

+,

+,

+,

+,

 or 

/2

/2

/2

/2

 appears.

Note: You cannot set the transmitting 
power when the weather radio is on.

When Auto Power Off is on, the 
transceiver automatically turns off 
when it is idle for 2 hours. Press any 
key to turn the transceiver back on. To 
turn the Auto Power Off function on or 
off, hold down 

MON/FUNC 

then press 

APO/HI/LO

$3 21

$3 21

$3 21

$3 21

 or 

$3 2)

$3 2)

$3 2)

$3 2)

 appears 

briefly.

USING KEY LOCK

You can lock the 

/ , 

/

SKIP

WX

DUAL

APO/HI/LO

, and 

QUIET/Q-SCAN

 

Summary of Contents for 5W














Reviews: