background image

4

R1CR 24 - RAD - ING - Manual - 1807.1_SK.2_MIAB3013_R7_PDX

_

P

ref

azione

_

EN

1.     

INTRODUCTION

WARNING

Before starting any operation it is mandatory to 
read this instruction manual, in relation to the 
activities  to  be  carried  out  as  described  in  each 
relevant section. Proper operation and optimal 
performance of the boiler are ensured by strict 
compliance with all the instructions given in this 
manual.

The installation, use and maintenance manual is 
an integral and essential part of the product and 
must be delivered to the user.

MANUAL USERS

The manual users are all those who install, use 
and maintain the boiler.

The  boiler  must  be  used  and  accessed  only  by 
qualified operators that fully read and understood 
the use and maintenance manual, paying particular 
attention to the warnings.

READING AND SYMBOLS OF THE MANUAL

To ease the understanding of this manual, 
recurrent symbols where used, in particular:

 

› On the outer margin of the page is placed a 

thumb index indicating the type of user to which 
the instructions in that section address.

 

› The titles are differentiated by thickness and 

size in accordance with their hierarchy.

 

› The images contain important parts described 

in the text, marked with numbers or letters.

 

› (See chap “chapter name”): this entry indicates 

another section in the Manual that you should 
refer to.

 

› Device: this term is used referring to the boiler.

 DANGER

It identifies an information related to a 

general danger that if not complied with, may cause 
serious personal damage or even death.

 ATTENTION

It identifies an information that if not 

complied with may cause small or medium level 
lesions to the person or serious deterioration to the 
boiler.

 WARNING

It identifies a precaution information that 

must be observed in order to avoid damaging the 
machine or parts of it.

MANUAL STORAGE

The manual must be carefully stored and replaced 
in case of deterioration and/or low legibility.

If you misplace the use and maintenance manual, 
you can request it from the Technical Support 
Centre giving the serial number and model of the 
boiler indicated on the plate placed on the right 
side of its casing.

As an alternative, the use and maintenance manual 
can be downloaded free from the on-line site www.
radiant.it, accessing the “download” section and 
entering the boiler model.

 INTRODUCTION 

Summary of Contents for R1CR 24









































































Reviews: