background image

Radial Engineering Ltd.

1588 Kebet Way, Port Coquitlam BC V3C 5M5

Tel: 604-942-1001 • Fax: 604-942-1010 • Email: [email protected]

RADIAL ENGINEERING LTD. (“Radial”) warrants this product to be free from defects in material and workmanship and will remedy 

any such defects free of charge according to the terms of this warranty. Radial will repair or replace (at its option) any defective 

component(s) of this product (excluding finish and wear and tear on components under normal use) for a period of three (3) years 

from the original date of purchase. In the event that a particular product is no longer available, Radial reserves the right to replace 

the product with a similar product of equal or greater value. In the unlikely event that a defect is uncovered, please call 604-942-1001 

or email [email protected] to obtain an RA number (Return Authorization number) before the 3 year warranty period expires. 

The product must be returned prepaid in the original shipping container (or equivalent) to Radial or to an authorized Radial repair 

center and you must assume the risk of loss or damage. A copy of the original invoice showing date of purchase and the dealer name 

must accompany any request for work to be performed under this limited and transferable warranty. This warranty shall not apply if 

the product has been damaged due to abuse, misuse, misapplication, accident or as a result of service or modification by any other 

than an authorized Radial repair center.

THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE ON THE FACE HEREOF AND DESCRIBED ABOVE. NO 

WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF 

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL EXTEND BEYOND THE RESPECTIVE WARRANTY 

PERIOD DESCRIBED ABOVE OF THREE YEARS. RADIAL SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY SPECIAL, INCI-

DENTAL OR CONSEQUENTIAL DAMAGES OR LOSS ARISING FROM THE USE OF THIS PRODUCT. THIS WARRANTY GIVES 

YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY DEPENDING ON WHERE 

YOU LIVE AND WHERE THE PRODUCT WAS PURCHASED.

RADIAL ENGINEERING

3 YEAR TRANSfERABLE WARRANTY

Radial LX-2™ User Guide - Part #: R870 1028 00 Copyright © 2017, all rights reserved.

Appearance and specifications subject to change without notice.

To meet the requirements of California Proposition 65, it is our responsibility to inform you of the following:

WARNING:

 This product contains chemicals known to the State of California to cause cancer, birth defects 

or other reproductive harm. 

Please take proper care when handling and consult local government regulations before discarding.

Summary of Contents for 9000-0033-6922












Reviews: