Racing RAC52PB-AB-3 Instruction Manual Download Page 2

Page: 2 / 22

ORIGINAL INSTRUCTIONS

CONTENT

1. SAFETY WARNINGS...............................................................................................................3

2. PRODUCT DESCRIPTION.......................................................................................................8

3. ASSEMBLY..............................................................................................................................11

4. FILLING………………………………………………………………………………………………..13

5. OPERATION............................................................................................................................14

6. MAINTENANCE & CARE........................................................................................................16

7. TROUBLE SHOOTING...........................................................................................................18

8. DECLARATION OF CONFORMITY........................................................................................19

WARRANTY...........................................................................................................................20

10. PRODUCT FAILURE...............................................................................................................21

11. WARRANTY EXCLUSIONS....................................................................................................22

Summary of Contents for RAC52PB-AB-3






















