background image

VBOX III User Guide 

 

 
 

 

Page 5 of 30 

15/07/2011 

Introduction 

 
The VBOX III represents the 3

rd

 generation of GPS data logging system from Racelogic. Using a powerful new GPS engine, the VBOX III can log GPS and 

other data at 100Hz. The logged data is stored directly onto a compact flash card for easy transfer to a PC. 
 
The VBOX III also sees the addition of 4 high-resolution analogue input channels to record data from external sensors and 2 CAN bus interfaces to allow 
connection of Racelogic input modules while simultaneously transmitting GPS data on the second bus. 
 
In line with previous VBOX models, the VBOX III is compatible with all of the existing peripherals including the Multifunction display, ADC03, TC8, FIM02 
and Yaw rate sensor. 

*See Note

 

Features 

 

  Non-contact 100Hz speed and distance measurement using GPS 

  12.5ms Latency 

  4 x 24bit synchronous differential analogue inputs ±50v  

  2 x CAN Bus interface 

  RS-232 serial interface 

  Compact Flash Interface 

  2 x 16bit User configurable analogue outputs 

  2 x Digital outputs  

  Brake trigger Input with 100KHz scan rate 

  Wide 5.3V to 30V operating range 

*See Note

 

  Logging rate selectable from 100Hz, 50Hz, 20Hz, 10Hz, 5Hz, 1Hz 

  40cm 95% CEP positional accuracy when used in conjunction with a 

Local DGPS Basestation. 

  2cm 95% CEP positional accuracy with a RTK GPS upgrade option 

and a RTK Basestation 

 
 

* RACELOGIC external modules such as Multifunction display only operate from a 12v vehicle 
supply. Therefore, when using external can modules, VBOX III supply must not exceed 15vDC. 

 

 

Summary of Contents for VBOX III































Reviews: