background image

1258 User Manual 

Operating Instructions 4-6  

                                         Racal Instruments 

©

 2005 

 

Configuring Remote Control 
Interfaces 

 

 

Ethernet 
Configuration. 

When connecting to the 1258 via Ethernet, the only setting that 
typically must be configured is the IP Address. The default IP 
Address is a standard internal-use IP Address, however, it may set 
to any other IP Address to suit your networking requirements.   The 
Port number for the 1258 is 49200.  This value cannot be changed.  
The remaining settings are used only when connecting the 1258 to 
a more complicated network.  In this case it may be necessary to 
ask a system administrator the proper way to configure the 1258. 
All settings can be reset back to their default configuration by 
selecting the Reset Configuration item in the Ethernet Menu.  Be 
sure to verify that the Ethernet cable is firmly plugged into the back 
of the 1258.   

Note:

 The Ethernet cable must be connected before power is 

applied to the 1258.

 

 

IEEE-488 (GPIB) 
Configuration. 

To communicate with the 1258 using GPIB, it is necessary to 
configure all settings. The Primary Address can be set to any value 
from 0 to 30.  The Secondary Address can be set to any address 
from 96 to 126 or set to 0 (disabled).  The 1258 GPIB settings can 
be configured from the front panel only.  All settings can be reset 
back to their default configuration by selecting the Reset 
Configuration item in the GPIB Menu. 

RS-232 Serial 
Configuration. 

When using RS-232 to communicate with the 1258, all protocol 
settings must be configured the same for the controller as for the 
1258.  Terminate all commands sent to the 1258 with a linefeed 
('\n') or a carriage return ('\r').  The 1258 will time out after 5 
seconds if a termination character is not received, and any 
characters received will be ignored.  RS-232 settings can be 
configured from the front panel only.  All settings can be reset back 
to their factory default configuration using the Reset Configuration 
option in the RS-232 Menu. 

 

Summary of Contents for 1258
















































Reviews: