INSTRUCTIONS
SMSLES2X13 INSTALLATION
INSTRUCTIONS
SMSLES2X13 INSTALLATION
RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install
and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]
RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install
and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]
Page 5
Page 6
TURN OFF POWER BY REMOVING POWER
FUSE OR TURNING OFF CIRCUIT BREAKER
BEFORE INSTALLATION.
• Total lighting load must not exceed:
500W LED SMSLES13 at 120 Volts
5 Amps, 450 Watts LED at 120 Volts with
0.8pF driver
5 Amps, 300 Watts LED at 120 Volts with
0.5pF driver.
To switch more wattage, an electrician
can install an additional relay.
• Line Carrier Remote Control Systems
such as X-10, Leviton or Radio Shack are
incompatible with sensors and cause false
activations.
• Do not install on circuits feeding motor
loads such as kitchen appliances, HVAC
equipment, washer/ dryer or garage door
openers.
• Sensor functions best when movement is
across its detection pattern, not towards
the sensor.
• Mount 6’-10’ high for optimum range
and direction.
(fig. 1.)
Less Sensitive
More Sensitive
Black
Black
Red
Red
(pigtail)
Ground
Ground
Power In
White
White
Fig: 3
Fig: 1
Fig: 2
Two LESLIE13 heads come pre-wired and assembled on
CU4 plate
, allowing for
mounting on round, rectangular or octagonal surface or recessed junction boxes. Apply
weatherproof silicone sealant around the edge of the
Junction Box
(not supplied)
. This is
especially important with an uneven wall surface.
1. Attach the
Universal Mounting Bar
with the screws provided to the
Junction Box
(fig. 3.)
In case of surface mount junction box, use with the
Metal Surface Plate
.
2. Use the ‘S’ shaped hands free
Hanging Hook
to hold the
CU4 plate
during wiring.
3. Bring power leads and
LESLIE13
head leads into
Junction Box
.
4. Strip off atleast 1/2” of insulation from all leads, and insert through openings in
Metal Surface Plate
(if used)
.
5. Attach ground wire to grounding screw on
Junction Box
. Complete wiring as
shown in wiring diagram section.
6. Align
Gasket, CU4 Plate
and
Metal Surface Plate
(for use with surface mounted
junction boxes)
to ensure proper seal.
7. Tighten
Center Screw
(make sure
O-Ring Gasket
is on the screw)
to attach
CU4 plate
to the box. Check that the
Gasket
is fully sealed.
8. Insert plastic
Finishing Cap
in the center of the
CU4 plate
for a weatherproof seal.
Use silicone sealant on all plugs and unused conduit entries.
9. Aim LESLIE13 heads in the desired direction and tighten locknut and arm screw.
Two SMSLES13 heads come pre-wired
and assembled along with SMS500 sensor
on CU4 plate, allowing for mounting on
round, rectangular or octagonal surface or
recessed boxes.
1. Connect the black fixture lead to the
(+) LINE supply lead.
(fig. 2.)
2. Connect the white fixture lead to the
(-) COMMON supply lead.
3. Connect the GROUND wire from
fixture to supply ground.
4. Red pigtail is only used to switch
remote or additional fixtures.
O-Ring
Gasket
CU4
plate
Gasket
Plug
Center
Screw
Finishing
Cap
Metal Surface
Plate
Hanging
Hook
Universal
Mounting Bar
Bar
Screws
Junction Box
(not supplied)
FIXTURE MOUNTING
ASSEMBLY AND WIRING
