background image

12

Toll Free Technical Assistance

If you need technical assistance, please do 

the following:

1. 

Re-read the Technical Tips sections of 

this manual.

2.

 Call the Tech Help Line at 888 722-

1000, 8AM to 4PM Eastern Time M-F and 

we will be glad to help you. Before you 

call, please have the following information 

handy:

a)

 Catalog number of your unit;

b)

 Wattage, types and locations of lights 

connected to the sensor;

c)

 The electrical circuit on which the sen-

sor is installed...what else does it feed? 

How is the sensor power switched?

d)

 This installation manual.

Note: RAB Lighting cannot give electrical 

wiring instructions by phone. Please 

consult a qualified electrician.

Note: These instructions do not cover 
all details or variations in equipment 
nor do they provide for every possible 
situation during installation operation or 
maintenance.

The following warranties apply to RAB Lighting, Inc. (“RAB”) 
products that meet all of the following conditions: (a) the 
product was purchased by the contractor or end-user 
from an authorized RAB distributor who purchased the 
product directly from RAB and from no other source; (b) if 
the product has been installed, the entire installation was 
performed by a licensed electrician or under the supervision 
of a licensed electrician and the product was in its original, 
unopened and new condition at the time of installation. 
RAB LIGHTING DISCLAIMS ALL REPRESENTATIONS AND 
WARRANTIES WITH RESPECT TO ALL OTHER PRODUCTS, 
INCLUDING WITHOUT LIMITATION PRODUCTS THAT HAVE 
BEEN PURCHASED FROM ANY PERSON OR ENTITY OTHER 
THAN AN AUTHORIZED RAB DISTRIBUTOR, OR INSTALLED 
BY ANY PERSON OR ENTITY OTHER THAN A LICENSED 
ELECTRICIAN OR UNDER THE SUPERVISION OF A LICENSED 
ELECTRICIAN, AND ALL PRODUCTS THAT ARE USED OR 
ARE OTHERWISE NOT IN THEIR ORIGINAL RAB LIGHTING 
PACKAGING AT THE TIME OF INSTALLATION.

Remedy.  RAB’s obligations for breach of warranty shall be 
limited to repair or replacement, at RAB’s option, of any 
products or parts which prove to be defective, provided that 
buyer gives RAB written notice and returns the defective 
product to RAB in accordance with RAB’s return material 
authorization (RMA) policies, and RAB confirms the defect. 
Buyer is responsible for all costs to de-install defective 
products and re-install replacement or repaired products 
and RAB shall not be liable for labor or other costs related to 
de-installation or re-installation.

DISCLAIMER.  THE FOREGOING WARRANTIES ARE 
IN LIEU OF, AND RAB EXPRESSLY DISCLAIMS, ALL 
OTHER REPRESENTATIONS, GUARANTEES AND 
WARRANTIES, EXPRESS OR IMPLIED IN FACT OR BY LAW, 
INCLUDING WITHOUT LIMITATION ALL WARRANTIES 
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR 
PURPOSE OR OTHERWISE. THE FOREGOING WARRANTIES 
STATE RAB’S ENTIRE AND EXCLUSIVE LIABILITY, AND BUYER’S 
SOLE AND EXCLUSIVE REMEDY, IN CONNECTION WITH THE 
PRODUCTS AND ALL PARTS, THEIR DESIGN, SUITABILITY FOR 
USE, INSTALLATION AND OPERATION.

LIMITATION OF LIABILITY.  RAB shall not be liable under 
any theory of relief, including without limitation breach of 
warranty, breach of contract, tort (including negligence), 
strict liability, or otherwise, arising out of or related to any 
breach of warranty, any RAB products and the use thereof, 
or any other acts or omissions of RAB for: (i) any indirect, 
incidental, special or consequential damages, whatsoever 
(including without limitation, loss of anticipated value of 
a business or its reputation) or (ii) any damage or loss in 
excess of the price actually paid by buyer to the authorized 
RAB distributor for the products that caused the damages. 
Any action by buyer must be commenced within one year 
after the cause of action has accrued.

Miscellaneous.  These product warranty terms shall be 
governed by the laws of the State of New York. Buyer 
consents to the personal jurisdiction and venue of the 
courts of the State of New York. Any legal or equitable 
claim of any nature arising hereunder shall be filed and 
maintained in the state or federal courts in the State of New 

RAB Lighting 

Product Warranties

York and buyer agrees that such courts are a convenient 
forum for adjudication. In the event that suit is necessary 
to recover amounts owed RAB, buyer shall be liable for 
reasonable attorney’s fees, interest and costs of collection. 
No agreement or understanding varying the terms and 
conditions hereof shall be binding upon RAB or buyer unless 
in writing and signed by duly authorized representatives of 
both parties. These product warranty terms shall inure to 
the benefit of and be binding upon the parties hereto and 
their respective successors and assigns.

Summary of Contents for Gotcha! Plus GT500














Reviews: