R82 X:panda Manual Download

Page: 34 / 36

160, 200, 240

200, 240, 280

260, 310, 360

340, 400, 460

(6¼,7¼,9¼")

(7¼,9¼,11")

(10¼,12,14")

(13¼, 15½, 18")

70, 90, 110

100, 120, 140

120, 145, 170

130, 190, 250

(2¾, 3½, 4¼")

(4, 4¾, 5½")

(4¾, 5¾, 6¾")

(5, 7½, 9¾")

160-260 (6¼-10¼")

220-330 (8½ -12¾") 260-390 (10¼-15¼") 380-530 (14¾-20½")

270-370 (10½-14½")

320-420 (12½-16½")

350-470 (13½-18¼")

490-680 (19-26½")

230 (9")

280 (11")

330 (12¾")

350 +50 (13½ +2")

310, 350, 390

380, 420, 460

470, 520, 570

590, 650, 710

(12, 13½, 15¼")

(14¾, 16¼, 18")

(18¼, 20¼, 22¼")

(23, 25¼, 27½")

-5° - +30°

0° - 15° *

0° - 15°

0° - 8°

6,5 kg (14,5 lb)

8,5 kg (18,5 lb)

11 kg (28,5 lb)

13 kg (28,5 lb)

45 kg (99 lb)

50 kg (110 lb)

60 kg (132 lb)

80 kg (176 lb)

45 kg (99 lb)

50 kg (110 lb)

57 kg (125,5 lb)

MEASUREMENTS

x:panda

Size 1

mm (inch)

x:panda

Size 2

mm (inch)

x:panda

Size 3

mm (inch)

x:panda

Size 4

mm (inch)

Seat width (A)

Width, thighs (A1)

Seat depth (B)

Back height (C)

Back width, top (F)

Total width, both legs in max abduction (G)

Back angle (a)

Abduction angle, each leg (a1)
* size 1 in the smallest position

Weight
Max load / user weight on

Max load / user weight at transportation

Further information regarding max. load/user weight and transportation:

www.R82.com/files/archive/Publications/Pdf/Chart_transport.pdf

Summary of Contents for X:panda




































Search results

Summary of Contents for X:panda

Reviews:

Related manuals for X:panda

Brands by name

Popular brands

R82 X:panda, Manual

Search results

Summary of Contents for X:panda

Reviews:

Related manuals for X:panda

Brands by name

Popular brands