background image

PJ500C-LCD, PJ700C-LCD  & PJ1000-LIGHT - User Manual

Version 1.0

© Copyright 2008

R.V.R. Elettronica SpA

Via del Fonditore 2/2c - 40138 - Bologna (Italia)

Telephone:   +39 051 6010506

Fax:    

+39 051 6011104

Email:  

[email protected]

Web:   

www.rvr.it

All rights reserved

Printed and bound in Italy. No part of this manual may be reproduced, 

memorized or transmitted in any form or by any means, electronic 

or mechanic, including photocopying, recording or by any informa-

tion storage and retrieval system, without written permission of the 

copyright owner.

File Name:

 

03_PJ500C-LCD_PJ700C-LCD&PJ1000light_ING_1.0.indd

Version:

 

1.0

Date:

 

24/06/2008
















Document History

Date

Version

Reason

Editor

24/06/08

1.0

First Edition

J.H. Berti

Summary of Contents for PJ700C-LCD





































Reviews: