JL Audio JX360/2 Owner'S Manual Download

Page: 1 / 17

Thank you for purchasing a JL Audio amplifier for

your automotive sound system.

Your amplifier has been designed and manufactured to exacting

standards in order to ensure years of musical enjoyment in your vehicle.

For maximum performance, we highly recommend that you have

your new amplifier installed by an authorized JL Audio dealer. Your

authorized dealer has the training, expertise and installation equipment

to ensure optimum performance from this product. Should you

decide to install the amplifier yourself, please take the time

to read this manual thoroughly so as to familiarize yourself

with its installation requirements and setup procedures.

If you have any questions regarding the instructions in this

manual or any aspect of your amplifier’s operation, please contact your

authorized JL Audio dealer for assistance. If you need further assistance,

please call our Technical Support Department

at (954) 443-1100 during business hours.

OWNER’S MANUAL

360W 2-Channel, Full-Range Amplifier

Summary of Contents for JX360/2


















Search results

Summary of Contents for JX360/2

Reviews:

Related manuals for JX360/2

Brands by name

Popular brands

JL Audio JX360/2, Owner'S Manual

Search results

Summary of Contents for JX360/2

Reviews:

Related manuals for JX360/2

Brands by name

Popular brands