background image

 

 
Thank you for selecting the R-Tech POWER TIG 210EXT Digital Inverter AC/DC Tig  Welder.   
 
The POWER TIG 210EXT Digital has many benefits over traditional TIG welders, including 9 
memory stores, advanced AC waveforms, pulse welding, slope up/down, remote foot option 
and an industrial 60% duty cycle. 
 
We want you to take pride in operating our POWER TIG 210EXT Digital as much pride as we 
have taken in making this product for you. Please read all information in this manual before 
operation 

 

 

PLEASE EXAMINE CARTON AND EQUIPMENT FOR DAMAGE IMMEDIATELY 

 

When this equipment is shipped, title passes to the purchaser upon receipt from the courier.  
Consequently all claims for material damaged in shipment must be made by purchaser against the 
transportation company used. 
 
Please record your equipment identification below for future reference. This information can be found on 
data plate at rear of machine. 

 

Product POWER TIG 210EXT DIGITAL 
 
Serial No. ___________________________________ 
 
Date of Purchase _____________________________ 
 
Where Purchased _____________________________ 
 
Whenever you request replacement parts or information on this equipment please always supply 
information you have recorded above 
 
This product is covered by our 2 year collect and return UK warranty, External items, torch, earth lead 
etc are covered by 3 months warranty. Any faults/damage found caused by customer will be charged 
pro-rata. 

 

 
Pay particular attention to the safety instructions we have provided you for your protection 
 
The level of seriousness to be applied to each section is explained below 

 

WARNING

 

 
This statement appears where the information must be followed exactly to avoid serious personal 
injury. 
 

CAUTION 

 
This statement appears where the information must be following to avoid a minor personal injury or 
damage to this equipment. 
 
 
 
 
 
 

Summary of Contents for POWER TIG 210EXT




























Reviews: