R.P.S. Corporation MAGNUM series Service Manual Download Page 30

Page: 30 / 134

Magnum Service Manual V1.0

3-10

SQUEEGEE SYSTEM

From

Page

Are there

missing parts?

Check to make sure the spacers, washers and

springs are all there and in working order.

Verify the measurement

where the front of the

triangle plate bolts to the

towbar. There should be

EXACTLY 7/8" clearance

on all machines except the

390/420 series.

It there proper

clearance there?

Check cable

clearance & slack

YES

Is there proper

clearance and slack?

Call the factory

YES

Does the machine

operate properly?

Bill the customer

Does the

machine work

properly?

Operate the

machine and verify

squeegee

operation

Adjust the

clearance.

Adjust clearance

and/or slack

Operate the

machine and verify

squeegee

operation

Replace parts and

adjust squeegee

YES

MAGNUM SQUEEGEE DIAGNOSTIC FLOW CHART

2 of 2

Summary of Contents for MAGNUM series







































































































































Search results

Summary of Contents for MAGNUM series

Reviews:

Related manuals for MAGNUM series

Brands by name

Popular brands

R.P.S. Corporation MAGNUM series, Service Manual

Search results

Summary of Contents for MAGNUM series

Reviews:

Related manuals for MAGNUM series

Brands by name

Popular brands