R.P.S. Corporation MAGNUM series Service Manual Download Page 121

Page: 121 / 134

RI-13

REPAIR INSTRUCTIONS

Magnum Service Manual V1.0

2/23/2006

253-05 TRANSAXLE R&R

Page 4 of 4

HELP HOTLINE: 800-634-4060

REINSTALLING TRANSAXLE

1. Strip red and black transaxle wires 5\16”.

2. Strip red and black harness wires 5\16”.

3. Crimp butt connectors on to transaxle wires.

4. Carefully put new transaxle into position.

5. Carefully put 2’’x4’’x12’’ boards under new tranaxle.

6. Reinstall transaxle mounts (Making sure to use alignment marks) and

install 5\16” nuts and lock washers and tighten.(See figure below)

7. Crimp butt connectors from transaxle wires back to harness and put

8”wire tie on the transaxle wires to the frame.

8. Reinstall the tires.

9. Remove jack stands.

Summary of Contents for MAGNUM series







































































































































Search results

Summary of Contents for MAGNUM series

Reviews:

Related manuals for MAGNUM series

Brands by name

Popular brands

R.P.S. Corporation MAGNUM series, Service Manual

Search results

Summary of Contents for MAGNUM series

Reviews:

Related manuals for MAGNUM series

Brands by name

Popular brands