background image

6

Improper treatment of generator can damage the unit and shorten its life.

service center.

 

WARNING!

Do not bypass any safety device.  Moving parts are covered with guards.  Make sure all protective covers are in place.

Never transport or make adjustments to this unit while it is running.

Never insert objects through cooling slots.

WARNING!

Never operate this unit if there are any broken or missing parts and only use

 our

 

Only use this unit as it is intended or serious injury or death could result.

SAFETY RULES

Increasing governing speed is dangerous which can result in personal injury and / or damaged equipment.

Decreasing governing speed adds an excessive load and can damage equipment.

Only when operating at the preset governing speed will this generator supply the correct rated frequency and voltage.

WARNING!

Never modify this unit in any way or modify governed speed.

Never handle the generator, electronic devices, or any cord while standing in water, while barefoot, or when hands or

feet are wet.

Always keep the generator dry.  Never operate generator in rain or under wet conditions.

Use a ground fault circuit interrupter (GFCI) in a damp or highly conductive area, such as metal decking or steel work.

Never plug electronic devices into generator having frayed, worn, or bare wires.  Never touch bare wires or make

contact with receptacles.

 

generator at all times.

If using the generator for back up power, notify the utility company.

install a transfer switch.  Failure to isolate the generator from the power utility could result in serious injury or death to 

electric utility workers.

WARNING!

This generator produces a very high voltage which could result in burn or 

electrocution causing serious injury or death.

Only operate generator on a level surface.

Always connect the nut and ground terminal on the frame to an appropriate ground source.

WARNING!

Generator must be properly grounded to prevent electrocution.

PROP 65 WARNING: This product contains chemicals known to the state of California to cause cancer and birth defects or 

other reproductive harm.

Summary of Contents for 2200I



























Reviews: