background image

ENGLISH

 

 

6 - Edition 10/2014 Cod. 2200780113  01 - 

 

 

TYPE 

Net Weight 

lb. (Kg.) 

 

Refrigerant 

R134a  

lb. (Kg.) 

 

 

Nominal 

Power  

HP (W) 

MAX. 

psi (bar) 

 

 

V230/115-60Hz 

V230-60Hz 

V115-60Hz 

V230-60Hz 

V115-60Hz 

V230-60Hz 

V115-60Hz 

 

QPNC 10 

41,9 (19) 

0,397  (0,180) 

0,161  (120) 

0,164  (122) 

0,040  (30) 

0,040  (30) 

0,201  (150) 

0,204  (152) 

232 (16) 

QPNC 15 

44,1 (20) 

0,463  (0,210) 

0,205  (153) 

0,212  (158) 

0,040  (30) 

0,040  (30) 

0,245  (183) 

0,252  (188) 

232 (16) 

QPNC 25 

55,1 (25) 

0,639  (0,290) 

0,312  (233) 

0,306  (228) 

0,040  (30) 

0,040  (30) 

0,353  (263) 

0,346  (258) 

232 (16) 

QPNC 35 

59,5 (27) 

0,970  (0,440) 

0,390  (291) 

0,386  (288) 

0,040  (30) 

0,040  (30) 

0,430  (321) 

0,426  (318) 

232 (16) 

QPNC 50 

59,5 (27) 

1,047  (0,475) 

0,417  (311) 

0,441  (329) 

0,040  (30) 

0,040  (30) 

0,457  (341) 

0,481  (359) 

232 (16) 

 

 

Reference conditions: 

Limit conditions:

 

Ambient temperature: + 100 °F  (+ 38 °C) 

Max. ambient temperature: + 115°F  (+ 46 °C) 

Inlet air temperature:  + 100 °F  (+ 38 °C) 

Min. ambient temperature:  + 34°F  (+ 1 °C) 

Working pressure: 102 psi  (7 bar) 

Max. inlet air temperature: + 131°F  (+ 55 °C) 

Dew point in pressure: + 39°F  (+ 4 °C) 

Max. working pressure: 232 psi  (16 bar) 

14.0 MACHINE ILLUSTRATION 

14.1 GENERAL LAY-OUT  

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

14.2 COMMAND AND CONTROL PANEL 

 

 

BEFORE CARRYING OUT THE OPERATION TEST, READ CAREFULLY AND ACQUIRE A GOOD KNOWLEDGE OF THE COMMAND 
FUNCTIONS. 

 

Ref. 1) Digital controller 
Ref. 8) Stop - Running button

 

 

 

 
 

 
 
 

 
 
 

 
 
 

 

ICON 

MODE 

FUNCTIONS 

 

ALARM 

OFF 

No active alarms 

ON 

Probe failure alarm 
High/Low temperature alarm 

 

COMPRESSOR 

OFF 

Dryer off 

FLASH 

Maintenance warning 

ON 

Dryer on 

 

FAN 

OFF 

Fan off 

FLASH 

n/a 

ON 

Fan on 

Alarms

 

Power ON

 

Fan ON

 

PDP temperature 

 

Unit °C or °F

 

Alarms led

 

 

 

 

Nominal 

Power

 

HP (W) 

Nominal 

Power

 

HP (W) 

FIG. 8 

Refrigerant compressor

 

Condenser

 

Motor fan

 

Evaporator

 

Condensate drain 

 

Hot gas by-pass valve

 

Refrigerant filter

 

Expansion capillary tube

 

 

 

 

 

 

FIG. 9 

 

 

Summary of Contents for QPNC 10













Reviews: